background image

Hotsy DB • 8.914-449.0 • Rev. 11/15

7

  

PRESSURE WASHER    

 

OPERATOR’S MANUAL

  

Pump 

— Develops high pressure.

Starter

 

Grip

— Used for starting the engine manu-

ally.

Spray Gun

 — Controls the application of water and 

detergent onto cleaning surface with trigger device. 
Includes safety latch.

Detergent Injector

 —  Allows you to siphon and mix 

detergents.

Wand

 — Must be connected to the spray gun. 

High Pressure Hose

 — Connect one end to water 

pump discharge nipple and the other end to spray 
gun.

Pump Protector 

— Cycles fresh cool water through 

pump when recirculating water reaches 140°F.

Note

:

 If trigger on spray gun is released for more 

than 1-2 minutes, water will leak from valve. Warm 

water will discharge from pump protector onto 

floor.  This system prevents internal pump dam

-

age.

COMPONENT IDENTIFICATION

Starter Grip

Trigger

Spray Gun

High Pressure 

Hose

Pump

Straight 

Through Wand

Pressure 

Nozzle

Garden Hose 

(not included)

Inlet 

Screen

Pump 

Protector

Unloader

Detergent 

Bucket  

(not included)

Detergent 

Injector

DB-3835, DB-3540

Models Only

Summary of Contents for DB-2323




















Reviews: