background image

    8.914-000.0, 8.917-410.0, 9.800-340.0  •   Rev. 09/10

3

 

 PRESSURE 

W

ASHER

 

OPERA

T

OR’S MANU

AL
  

IMPORTANT SAFETY INFORMATION

TRIGGER GUN KICKS 

BACK - HOLD WITH 

BOTH HANDS

WARNING

WARNING: Grip cleaning wand 
securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

RISK OF INJECTION 
OR SEVERE INJURY 

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure devel-
oped by these machines will 
cause personal injury or equip-
ment damage. Keep clear of 
nozzle. Use caution when oper-
ating. Do not direct discharge 
stream at people, or severe in-
jury or death will result. 

 

 

 10. To reduce the risk of injury, close supervision is 

necessary when a machine is used near children. 
Do not allow children to operate the pressure 
washer. 

This machine must be attended during 

operation.

 11.  Never make adjustments on machine while in op-

eration. 

 12. Be certain all quick coupler fi ttings are secured 

before using pressure washer.

WARNING

PROTECT FROM 

FREEZING

WARNING: Protect machine from 
freezing.

13.  To keep machine in best 
 

operating conditions, it is 

 

important you protect machine 

 

from freezing. Failure to protect 

 

machine from freezing could 

 

cause malfunction of the 

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol-
low storage instructions specifi ed in this manual.

14.   Inlet water must be clean fresh water and no hotter 

then 90°F.

 15. Manufacturer will not be liable for any changes 

made to our standard machines or any components 
not purchased from us.

 16.  The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING

RISK OF INJURY 

FROM FALLS WHEN 

USING LADDER.

WARNING: Be extremely careful 

when using a ladder, scaffolding or any other rela-
tively unstable location. The cleaning area should 
have adequate slopes and drainage to reduce the 
possibility of a fall due to slippery surfaces.

 17. Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

 18.  Do not operate this machine when fatigued or under 

the infl uence of alcohol, prescription medications,  
or drugs.

Follow the maintenance instructions  
specifi ed in the manual. 

Summary of Contents for BDE-505009B















Reviews: