background image

PCA • 8.917-985.0 • Rev. 10/12

PRESSURE 

W

ASHER  

T

roub

leshooting  Guide

14

PROBLEM

POSSIBLE CAUSE

SOLUTION

ENGINE OPERATES 
FOR 15 MINUTES 
THEN STOPS

Not enough gas or engine oil

Fill tank with gas. Check oil level.

Vapor lock developed by heat of day

Keep gas tank full to avoid vapor locking.

Obstruction in fuel fi lter

Clean or replace fuel fi lter.

ENGINE LACKS 
POWER

Dirty air fi lter

Replace air fi lter.

ENGINE FALTERS

Choke is opened too soon

Move choke to halfway position until engine 
runs smoothly.

WATER DRIPPING 
FROM UNDER PUMP

Piston packing worn

Call local distributor.

O-Ring plunger retainer worn

Call local distributor.

Cracked piston

Call local distributor.

OIL DRIPPING 
FROM UNDER PUMP

Oil seal worn or damaged

Call local distributor.

WATER LEAKING 
FROM PUMP 
PROTECTOR

Spray gun closed with machine 
running 5 minutes or longer

Open spray gun or turn off machine.

Excess water supply pressure

Place a pressure regulator at end of 50' 
garden hose.

NO DETERGENT

Detergent suction tube not properly 
connected to machine

Check connection.

Detergent is too thick

Dilute detergent. For best results, use 
manufacturers detergent.

Detergent fi lter valve is at lowest 
setting

Set detergent fi lter valve to a higher setting.

Filter on detergent suction tube is 
clogged

Run warm water through fi lter to remove 
debris.

Damaged or clogged detergent suc-
tion tube

Remove obstruction or replace detergent 
suction tube.

A high pressure nozzle is attached.

Replace with black detergent nozzle. 

Discharge nozzle is obstructed

Blow out or remove debris with fi ne needle.

GARDEN HOSE 
CONNECTION 
LEAKS

Loose fi ttings

Tighten fi ttings.

Missing/worn rubber washer

Insert new washer.

SPRAY WAND 
LEAKS

Spray wand not properly attached

Slide the spray wand into the gun. Turn the 
wand collar clockwise onto the spray gun 
threads until tight.

Broken o-ring

Call local distributor and order an o-ring.

PUMP IS NOISY

Pump is sucking air

Check that hoses and fi ttings are air tight. 
Turn off machine and purge pump by 
squeezing trigger gun until a steady fl ow of 
water emerges through nozzle. 

TROUBLESHOOTING

Summary of Contents for 1.107-124.0



















Reviews: