background image

7

GB

Indicator lights

The indicator lights provide important information.
This is what they can tell you:

Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has begun, 
the indicator lights switch on one by one to indicate which 
phase of the cycle is currently in progress.

Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator 
light will illuminate. 
If the selected function is not compatible with the pro-
grammed wash cycle, the corresponding indicator light will 
flash and the function will not be activated.
If a function which is incompatible with another function 
selected previously, only the most recent selection will 
remain active.

 

Door locked indicator light

If this indicator light is on, the appliance door is locked to 
prevent it from being opened accidentally; to avoid any 
damage, wait for the indicator light to switch off before you 
open the appliance door.

!

 

If the START/PAUSE indicator light (orange) flashes 

rapidly at the same time as the function indicator light, 
this indicates a problem has occurred (see “Troublesho-
oting”).

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, 
then only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indica-
tor light will flash.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a 
fixed manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the 

 indicator light will switch on. The DOOR LOCKED indicator light will switch off, 

indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum 
dries completely. Switch the washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Pump out

End of wash cycle

Summary of Contents for WML 730 A

















Reviews: