background image

The Dispenser Drawer

STEP 3

Adding Fabric Conditioner

Dispensing Powder Detergent

Dispensing Liquid Detergent

Index:

1. Drawer release latch

2. Pre-wash detergent compartment

Maximum 200ml powder or 

100ml liquid

3. Main detergent compartment

Maximum 400ml powder or 

200ml liquid

4. Grate

5. Fabric conditioner compartment

120ml maximum

1

2

3

4
5

To achieve the best wash results the

manufacturer’s recommended amount

of detergent should be measured and

added to the main detergent 

compartment (II symbol) (max. 400ml).

Alternatively you can obtain a liquid

detergent flap, a barrier for the dispenser

drawer.

Contact Hotpoint Genuine Parts and

Accessories (see Key Contacts)

Pour the recommended

amount of fabric 

conditioner into the 

compartment 

(flower symbol).

Do not exceed the 

maximum fill line.

Pre-wash 

Programme A

When selecting programme A,

add detergent to both the 

pre-wash compartment (symbol)

and the main wash compartment

(II symbol).

DO NOT use in drum dosing

devices with the Pre-wash 

programme, A.

WARNING:

Do not put any items into 

the drawer, other than 

detergents designed to be 

released from the drawer, as 

they may cause damage or 

blockage.

We recommend the use of a detergent dosing ball, as provided by your detergent

manufacturer.

Summary of Contents for WMA5












Reviews: