Preparation before using
2
Placement
New refrigerator
Transportation and placement of the refrigerator
Transportation
Warning
Attention
3
Correct application of the refrigerator
Ensure that the refrigerator is placed correctly and stably.
Be aware of all safety matters needing attention.
After connecting electricity, it will enter into ex-factory state.
1.Connect the electricity
2.Put food into the refrigerator
ƽ
Except the solutions recommended by the manufacturer, do not use mechanical
equipment or other means to accelerate defrosting.
ƽ
Except the types recommended by the manufacturer, do not use electrical appliance
inside food closet.
ƽ
The refrigerator is provided with R600a refrigerant and cyclopentane foaming
material, and both are combustible materials. Obsolete refrigerator should be
isolated from fire and combustion treatment is forbidden.
ƽ
foam pads and gummed paper inside;
ƽ
Use warm and wet cleaning cloth to wipe the refrigerator's interior and exterior (add a
little detergent in the warm water and use clean water to clean up);
ƽ
Prepare a separating grounding receptacle with both polarities. Do not share multi-
purpose socket with other electrical appliances;
ƽ
Connect earth wire. Earth electrode of the socket must be equipped with a reliable
grounding wire.
Remove all packing materials before using, including bottom seating washer and
ƽ
Do not invert, traverse, press and shake the refrigerator. When moving the
refrigerator, angle of inclination shall not be larger than 45
°
.
ƽ
When moving, do not make excessive pressure to the door or top cover, otherwise
deformation will occur.
ƽ
Slightly remove the refrigerator backward (less than 20
°
) to rear truckle roll a short
distance.
ƽ
sunlight. In order to avoid rust or reduce insulation result, please do not place it at
damp and watered place.
ƽ
Top space for the refrigerator shall not be less than 30cm. Distance against two sides
shall not be less than 10cm, Distance against to the wall shall not exceed 75mm,
providing convenience to open and close the door and disperse the heat.
ƽ
Place the refrigerator on a flat and solid floor. (if it is not stable, you can regulate the
regulating legs)
Place the refrigerator at a ventilative place, far away from heat source and direct
Make sure the power line is not pressed by the refrigerator or other articles.
Before connect the power line, make sure the voltage range of the refrigerator
accord with that of the power supply.
Suggestion: after working a time, the refrigerator will arrive store temperature or after
the first stop of the compressor, put food into it, which is beneficial to retain
freshness.
Note: if the set temperature is altered or new food is put in, temperature
inside the box will achieve the balance after a time, which is determined by
the temperature alteration degree, temperature of ambient environment,
opening frequency, quantity of the food inside and so on.
ƽ
Generally, temperature inside refrigerating chamber is below -18
ć
. Food needing long-
term storage shall be put in refrigerating chamber.
ƽ
Quick-frozen food shall be put into the refrigerating chamber as soon as possible before
defreezing.
ƽ
Hot food should be put into refrigerating chamber after it cools down to room temperature.
ƽ
Fruit and vegetable should not be put into refrigerating chamber. In order to avoid freezing
and rupture, glass container with liquid should not be put into the refrigerating chamber.
ƽ
Quick-frozen food should be stored by category. Food in the same kind should be put into
together. Thus, energy conservation can be realized by reducing opening frequency.
Refrigerating chamber's drawer
It is for food needing freezing. A block of meat should be put into the drawer after being sliced
for convenience. When take out the food, pull our the drawer at first, then horizontally push
the tray above the drawer inward, and then take out the food under the drawer,
Note: close the drawer, after using the refrigerating chamber.
Summary of Contents for UPAH 1832 F
Page 2: ......
