background image

8

GB

Control panel

PROGRAMMES

Knob

Indicator

ON/OFF

Button

OPTION

Buttons & Lights

START/PAUSE

Button & Light

Empty Water

Light

Clean Filter

Light 

Clean Condenser 

Light

Progress or Delay 

Lights

ON/OFF/Reset button

Pressing the button normally will cause the machine to switch 
on or off. If the button is pressed for 3 seconds while the dryer 
is in function, the machine will switch off and the running cycle 
will reset.  

Programme selection knob 

Allows for setting the programme: turn until the indicator points 
towards the desired programme 

(see Starting and selecting 

a programme).

Options buttons

Allow for selecting the options available for the selected pro-
gramme. The relative indicator lights turn on when the option 
has been selected 

(see Programmes and options).

START/PAUSE button and indicator light 

When the green light flashes slowly, press the button to start 
the programme. When the cycle is under way, the indicator 
light remains on. To put the programme into pause mode, 
press the button again; the indicator light will turn and start 
flashing again.
To resume the programme from the point it was interrupted, 
press the button again

 (see Start and programme selection).

Indicator lights

“Maintenance” indicator lights

The indicator lights provide important information. They indi-
cate the following:
The “Empty water container” indicator light 

 signals that the 

water container must be emptied. 
If the water container fills during the course of the programme, 
the LED lights up. The dryer automatically starts a COOL 
TUMBLE cycle and the START/PAUSE LED flashes orange. 
Press the START/PAUSE button to resume the cycle from the 
point it was interrupted. 

In order to avoid this procedure, always empty the water con-
tainer after using the tumble dryer 

(see Care and maintenance).

Before each programme, the “Clean filter” indicator light 

 

signals that it is essential to clean the filter each time before 
using the tumble dryer 

(see Care and maintenance).

 CARE LABEL

Always check the care labels, especially when placing garments in 

the tumble dryer for the fi rst time. Below are the most commonly 

used symbols:
   

May be tumble dried.

 

Do not tumble dry.

 

Tumble dry – high heat.

 

Tumble dry – low heat.

The “Clean condenser unit” indicator light   signals that it is essential to 
clean the condenser regularly 

(see Care and maintenance).

“Drying phases” indicator lights

The 

 indicator light signals that the drying phase is running.

The 

 indicator light signals that the cooling phase is running.

The 

END 

indicator light signals that the programme has ended.

“Delay timer” indicator light

If the ”Delay timer” option has been activated

 

(

see “Programmes and 

options”

), after the programme has started, the indicator light corre-

sponding to the chosen delay time will start flashing:
As time passes, the remaining delay will be displayed and the corre-
sponding indicator light will flash:
Once the set delay time ends, the flashing LED will turn off and the set 
programme will start.

Summary of Contents for TCFS 835B













Reviews: