THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance, please
register your product on
www.hotpoint.eu/register
Policies, standard documentation, ordering of spare parts and additional product information can be
found by:
• Visiting our website
docs.hotpoint.eu
and
parts-selfservice.whirlpool.com
• Using QR Code
• Alternatively,
contact our After-sales Service
(See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identifi cation plate.
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your product on
www.whirlpool.com.sg
For Singapore Warranty, please scan QR code or visit the website: www.whirlpool.com.sg
Standard documentation and additional product information can be found by:
• Visiting our website
www.whirlpool.com.sg
• Using QR Code
• Alternatively,
contact our After-sales Service
(+65 6250 6888). When contacting our After-sales Service,
please state the codes provided on your product’s identifi cation plate.
EN
Quick guide
Before using the appliance carefully read the Safety
Instructions.
xxxxxxxxxxxx
xxxx
*MAX LOAD 8 kg
(Dry load)
Power consumption
off-mode (Po) - Watts
0.15
left-on mode (Pl) - Watts
0.15
Programmes
kg
kWh
Minutes
Eco Cotton
*
8
4.75
156
Eco Cotton
4
2.55
87
Synthetics
4
2.26
110
*This is the most efficient programmes in terms of energy consuption
and is suitable for drying normal wet cotton laundry. The values on
the Energy Label are based on this programme.
*MAX LOAD 9 kg
(Dry load)
Power consumption
off-mode (Po) - Watts
0.15
left-on mode (Pl) - Watts
0.15
Programmes
kg
kWh
Minutes
Eco Cotton
*
9
5.23
162
Eco Cotton
4.5
2.79
92
Synthetics
4
2.26
110
*This is the most efficient programmes in terms of energy consuption
and is suitable for drying normal wet cotton laundry. The values on
the Energy Label are based on this programme.
The values reported in
the table are obtained with the condensed water drained externally
through the drain hose.
CARE AND MAINTENANCE
WARNING: unplug the dryer during the cleaning and
maintenance procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and empty it into a sink or
other suitable drain, then place it back properly. Do not use the
dryer without having inserted the container back in place.
Cleaning the door filter after each cycle (see Fig. B).
Pull the filter out and clean it by removing the lint from the filter
surface under running water or using a vacuum cleaner. For optimal
performance, dry up the filter before inserting it back in place.
Do not use the dryer without having reinserted the filter in place.
Remove the door filter as described below:
1. Open the door and pull the filter upwards.
2. Open the filter and remove the lint from all its parts. Replace
the filter correctly making sure it is fully seated.
The filter is an essential part for drying. It is intended to
collect the lint formed during the drying process. If the
filter is clogged, the air flow inside the dryer can become
seriously affected: this will increase the drying time and
energy consumption, and could damage the dryer.
If this
procedure is not carried out properly, the dryer may not
start.
Cleaning the condenser unit (see Fig. C).
Remove the condenser unit regularly (monthly) and clean off
any fluff deposits from the plates by running cold water along
its rear end.
The light on after several cycles is just a reminder to
carry on this activity periodically.
Removing the condenser:
1. Open the condenser cover, unlock the three catches by
turning them 90° anticlockwise.
2. Pull on the grip to remove the condenser.
3. Clean the surface of the seals.
4. Replace the unit with the arrows pointing upwards, while
making sure that the catches are securely fixed.
PRODUCT DESCRIPTION
1.
Water tank
2.
Air intake
3.
Door filter
4.
Condenser unit
5.
Condenser cover
A
B
C
1
3
2
4
5
Cleaning the tumble dryer
•
The external metal, plastic and rubber parts can be cleaned
with a damp cloth.
•
Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
•
Do not use solvents or abrasives.
