background image

GB

5

Installation

!

 Before placing your new appliance into operation please read

these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.

!

 Please keep these operating instructions for future reference.

Pass them on to possible new owners of the appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to
operate correctly and save energy.

3. Leave a space of at least 10 cm between the top part of the

appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat (direct

sunlight, electric stove, etc.).

5. In order to maintain the correct distance between the

appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.

Levelling

1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by

tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical
socket ensure the following:

• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located on the
bottom left side of the fridge (e.g. 150 W).

• The voltage must be in the range between the values indicated

on the data plate located on the bottom left side (e.g. 220-240V).

• The socket is compatible with the plug of the appliance. If the

socket is incompatible with the plug, ask an authorised
technician to replace it (

see Assistance

). Do not use

extension cords or multiple sockets.

!

 Once the appliance has been installed, the power supply cable

and the electrical socket must be easily accessible.

!

 The cable must not be bent or compressed.

!

 The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

!

 The manufactur

 The manufactur

 The manufactur

 The manufactur

 The manufacturer declines any liability should these safety

er declines any liability should these safety

er declines any liability should these safety

er declines any liability should these safety

er declines any liability should these safety

measur

measur

measur

measur

measures not be observed.

es not be observed.

es not be observed.

es not be observed.

es not be observed.

Your appliance is supplied with a 13amp fused plug that can be
plugged into a 13amp socket for immediate use.  Before using
the appliance please read the instructions below.

WARNING:
THIS APPLIANCE MUST BE EARTHED.

Replacing fuse covers:

When replacing a faulty fuse, a 13amp ASTA approved fuse to
BS 1362 should always be used and the fuse cover re-fitted.
If the fuse cover is lost, the plug must not be used until a
replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct
colour as indicated by the coloured marking or the colour that is
embossed in words on the base of the plug.

Changing the plug:

Removing the plug

If your appliance has a non-rewireable moulded plug and you
should wish to remove it to add a longer cable or to re-route the
mains cable through partitions, units etc. please ensure that either:
-

The plug is replaced by a fused 13amp re-wireable plug

bearing the BSI mark of approval.

or
-

The mains cable is wired directly into a 13amp cable outlet,

controlled by a switch (in compliance with BS 5733) which is
accessible without moving the appliance.

Disposing of the plug

Cut off and dispose of the supplied plug if it does not fit your socket.
The cable should be cut as close as possible to the moulded plug.

Remove the fuse.

WARNING:
To avoid a shock hazard do not insert the discarded plug
into a socket anywhere else.

Fitting a new plug

IMPORTANT:

WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...

Green and Yellow

- Earth

Blue

- Neutral

Brown

- Live

As the colours of the wires in the mains lead may not correspond
with the coloured markings identifying the terminals in your plug,
proceed as follows:

-

Connect 

Green and Yellow

 wire to terminal marked 

'E'

 or 

or coloured Green and Yellow.

-

Connect 

Brown

 wire to terminal marked 

'L'

 or coloured red or

brown.

-

Connect 

Blue

 wire to terminal marked 

'N'

  or coloured Black

or Blue.

If a 13amp plug (BS 1363) is used it must be fitted with a 13amp fuse.

If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.

CE Marking certifies that this appliance conforms to the
following EEC directives:
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC &
93/68/EEC

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24

Summary of Contents for FZS 175









Reviews: