19
GB
Function Effect
Comments
Enabled with
programmes:
Super
Wash
All ows f or an
i mpeccable
wash, vi si bl y
whit er than a
st andard
Cl ass A wash.
This functi on i s incompat ible wit h t he RAPI D f unct i on.
1, 2, 3, 4,
5, 6, 7, 8
Easy i ron
This opti on
reduces t he
amount of
creasi ng on
f abri cs,
maki ng t hem
easi er to i ron.
When t hi s fu ncti on i s set , programmes 6, 7, 8, 11 and
Deli cat e rinse wi ll end wit h t he l aundry lef t t o soak
(Anti -crease) and t heEasy Iron but ton fl ashes:
- t o concl ude the cycl e, press t he START/RESET or
t he EASY IRON bu t t on;
- t o run the drai ni ng cycle alone, set t he knob t o
t he relat i ve symbol and press t he START/RESET
bu t t on.
All
programmes
excluded for
1, 2, 9, 10
and
Draining.
Rapi d
Cuts t he
durat ion of
t he wash
cycl e by 30%.
This functi on i s incompat ible wit h t he SUPER WASH
f u nct ion.
1, 2, 3, 4,
5, 6, 7, 8
Rinses
Personalisations
Setting the spin cycle
If, when the appliance is switched on, the KNOB is positioned on a
programme with a spin cycle, a fixed
appears. Press button
and the maximum spin speed allowed for the programme set will be
displayed, and the
the
icon goes on. Press it again and the
values lower until they reach OFF, which indicates that the spin
cycle has been excluded (press it again to go back to the maximum
value); stop on the desired speed, after approximately 2 seconds
the setting is accepted: the symbol
remains fixed.
The spin cycle setting is enabled with all the programmes except for
11 (curtains, silk) and the Draining cycle.
Setting the temperature
If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs
to be regulated, a fixed
appears. Press button
and the maximum temperature allowed for the programme
set will be displayed and the
icon flashes. Press it again and the temperature lowers until it reaches OFF,
which indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value,
after approximately 2 seconds the setting is accepted: the symbol
remains fixed.
The temperature adjustment is enabled with all wash programmes.
Setting the Delay Timer
Press the button
and you will see the word OFF on the display, while the relative symbol flashes.
Press the button again and "1h" appears, that is, a delay of one hour (this can reach up to 24h); stop on the
"desired" delay; after approximately 2 seconds the setting is accepted, following which, the time for the set
programme appears on the display and the symbol
remains on.
If you now press the START/RESET button, the set "delay" appears; this decreases every hour until the start of
the cycle. In this phase, the "delay" can only be modified by decreasing it.
The Delay Timer regulation is enabled with all programmes.
Keyboard lock
(See page 17)
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note:
The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
If you set a function that is incompatible with another function you selected previously, only the last one selected
will be enabled.
Summary of Contents for AVTF 104
