Hoshizaki KM-515MAH Service Manual Download Page 56 | Manualshive

Page: 56 / 57

background image

56

B. Maintenance

IMPORTANT

This icemaker must be maintained individually, referring to the instruction
manual and labels provided with the icemaker.

1. Stainless Steel Exterior

To prevent corrosion, wipe the exterior occasionally with a clean, soft cloth. Use a damp
cloth containing a neutral cleaner to wipe off oil or dirt build up.

2. Storage Bin and Scoop

• Wash your hands before removing ice. Use the plastic scoop provided (bin accessory).
• The storage bin is for ice use only. Do not store anything else in the storage bin.
• Clean the scoop and the storage bin liner using a neutral cleaner. Rinse thoroughly

after cleaning.

3. Air Filters (air-cooled model only)

Plastic mesh air filters remove dirt and dust from the air, and keep the condenser from
getting clogged. As the filters get clogged, the icemaker’s performance will be reduced.
Check the filters at least twice a month. When they are clogged, use warm water and a
neutral cleaner to wash the filters.

4. Condenser (air-cooled and remote air-cooled models only)

Check the condenser once a year, and clean the coil if required by using a brush or
vacuum cleaner. More frequent cleaning may be required depending on location.

C. Preparing the Icemaker for Long Storage

CAUTION

When shutting off the icemaker for an extended time, drain out all water from
the water tank and remove the ice from the storage bin. The storage bin should
be cleaned and dried. Drain the icemaker to prevent damage to the water
supply line at sub-freezing temperatures, using air or carbon dioxide. Shut off
the icemaker until the proper ambient temperature is resumed.

When the icemaker is not used for two or three days, it is sufficient to only move the control
switch to the "OFF" position, unless the icemaker will be at sub-freezing temperatures.

1. On water-cooled model only, first remove the water from the water-cooled

condenser:

1) Turn off the power supply and remove the front panel and right side panel.
2) Close the condenser water supply line shut-off valve.
3) Open the condenser water supply line drain valve.
4) Attach a compressed air or carbon dioxide supply to the condenser water supply line

drain valve.

«
...
54
55
56
57
»

Summary of Contents for KM-515MAH


























































Reviews:

No comments

Related manuals for KM-515MAH

Brand: 3M Pages: 12

Brand: Faema Pages: 60

Brand: Faema Pages: 105

PROFESSIONAL Series

Brand: CAFÉ ROYAL Pages: 52

Brand: Salton Pages: 16

Korinto UL 120V

Brand: Necta Pages: 100

the Choc & Cino LMF200

Brand: Breville Pages: 16

Truck Coffee Maker

Brand: Quintezz Pages: 5

ESPRESSO DELUXE

Brand: Gaggia Pages: 53

GS-3405T Series

Brand: Gainscha Pages: 35

Brand: Optimum Pages: 51

Brand: Krups Pages: 33

Brand: Texlabel Pages: 33

Brand: Proctor-Silex Pages: 28

Brand: Mistral Pages: 28

Brand: Yoo Digital Pages: 40

Brand: Philips Saeco Pages: 60

ECAM23 13 Series

Brand: DeLonghi Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands