background image

ENGLISH

12

F. Water Supply and Drain Connections

See Figs. 5 

 WARNING

Water supply and drain connections must be installed in accordance with applicable 

national, state, and local regulations.

NOTICE

• Normal operating water temperature should be within 7°C to 32°C. Operation of 

the appliance, for extended periods, outside of this normal temperature range may 

affect appliance performance.

• Water supply pressure must be a minimum of 0.07MPa (0.7bar) and a maximum 

of 0.78MPa (7.8bar). If the pressure exceeds 0.78MPa (7.8bar), the use of a 

pressure reducing valve is required.

• To prevent damage to the appliance, do not operate the appliance when the water 

supply is off, or if the pressure is below 0.07MPa(0.7bar). Do not run the appliance 

until the proper water pressure is reached.

• External filters, strainers, or softeners may be required depending on water quality. 

Contact your local Hoshizaki Certified Service Representative or local Hoshizaki 

distributor for recommendations.

• A plumbing permit and services of a licensed plumber may be required in some areas.
• The icemaker drain line, ice storage bin drain line, and water-cooled condenser drain line  

must be run separately. The condensation drain line can be connected to the icemaker 

drain line or can be run separately. 

• Drain lines must have 2 cm fall per 1 m on horizontal runs to get a good flow. A vented tee 

connection is also required for proper flow.

• Drain lines should not be piped directly to the sewer system. An air gap of a minimum of 

5 vertical centimeter  should be between the end of the drain pipes from the icemaker and 

condensation drain, ice storage bin, and water-cooled condenser and the floor drain.

Summary of Contents for KM-470AJ


































Reviews: