Hoshizaki KM-320MAH-E Service Manual Download Page 46

Page: 46 / 59

F. Diagnostic Charts

1. No Ice Production

No Ice Production - Possible Cause

1. Power Supply

a) Off, blown fuse, or tripped breaker.
b) Not within specifications.

2. Fuse (Power Cord)

a) Blown.

3. Main Transformer

(230VAC/115VAC)

a) Coil winding open or shorted.

4. Fuse (Control Box)

a) Blown.

5. Thermostatic Bin Control

(KM-320MAH-E and
KM-650MAH-E
Aux. Code U-0 and Earlier;
KM-515MAH-E
Aux. Code U-1 and Earlier)
See "IV.C. Bin Control Check"

a) Tripped with bin filled with ice.
b) Ambient temperature too cool.
c) Set too warm.
d) Bulb out of position.
e) Open contacts, defective.

6. Control Switch

a) In "OFF" or "WASH" position.
b) Bad contacts.

7. High-Pressure Switch

a) Dirty condenser.
b) Fan motor not operating.
c) Refrigerant overcharged.
d) Bad contacts.
e) Refrigerant lines or components plugged.

8. Control Transformer

(115VAC/10.5VAC)

a) Coil winding open or shorted.

9. Control Board

See "IV.B. Control Board Check"

a) In alarm.
b) Yellow "BC OPEN" LED on (bin full).
c) Defective.

10. Mechanical Bin Control

(KM-320MAH-E and
KM-650MAH-E
Aux. Code U-1 and Later;
KM-515MAH-E
Aux. Code U-2 and Later)
See "IV.C. Bin Control Check"

a) Tripped with bin filled with ice.
b) Actuator does not move freely.
c) Defective.

11. Water Supply

a) Water supply off or improper water pressure.
b) External water filters clogged.

12. Inlet Water Valve

a) Screen or orifice clogged.
b) Coil winding open.
c) Water valve open in freeze cycle.

13. Float Switch

See "IV.D. Float Switch Check
and Cleaning"

a) Float does not move freely.
b) Defective.

Summary of Contents for KM-320MAH-E




























































Search results

Summary of Contents for KM-320MAH-E

Reviews:

Related manuals for KM-320MAH-E

Brands by name

Popular brands

Hoshizaki KM-320MAH-E, Service Manual

Search results

Summary of Contents for KM-320MAH-E

Reviews:

Related manuals for KM-320MAH-E

Brands by name

Popular brands