background image

23

KM-1301S_J(Z)

KM-1601S_J(Z)

KM-1900S_J(Z)

KM-1301S_J(Z)3
KM-1601S_J(Z)3

KM-1900S_J(Z)3
KM-2200S_J(Z)3
KM-2600S_J(Z)3

BLACK

 WARNING

ELECTRICAL CONNECTION

THIS UNIT MUST BE GROUNDED

Failure to properly ground or wire 
this unit could result in death, 
serious injury, or severe damage to 
the icemaker.
The transformer’s voltage tap switch 
must be positioned to match incoming 
voltage at startup.
See diagram below.

4A5812-010

208-230/60/1

JUNCTION BOX

20

8-2

30

V

BROWN

L1

L2

 WARNING

ELECTRICAL CONNECTION

THIS UNIT MUST BE GROUNDED

Failure to properly ground or wire 
this unit could result in death, 
serious injury, or severe damage 
to the icemaker. The white lead 
must be connected to the neutral 
conductor of the power source.
See diagram below.

4A5700-010

208-230/60/1

(3 wire with neutral for 115V)

JUNCTION BOX

208-230

V

BLACK

BROWN

L1

L2

WHITE

N

115

-

120V

Fig. 7

BROWN

 WARNING

ELECTRICAL CONNECTION

THIS UNIT MUST BE GROUNDED

Failure to properly ground or wire 
this unit could result in death, 
serious injury, or severe damage to 
the icemaker.
This unit must be connected to a 
three-phase power source.
The transformer’s voltage tap switch 
must be positioned to match incoming 
voltage at startup.
See diagram below.

208-230/60/3

4A5701-010

JUNCTION BOX

208-230

V

BLACK

L1

L3

RED

L2

208- 230V

208- 230V

Summary of Contents for KM-1301SRJZ














































Reviews: