Hoshizaki KM-1301SRJZ Instruction Manual Download Page 15 | Manualshive

Page: 15 / 45

Hoshizaki KM-1301SRJZ Instruction Manual Download Page 15

15

Rear

Top

Units: mm [in.]

Icemaker
Model

URC-14FZ Heat of Rejection

AT 90°F (32°C)
WT 70°F (21°C)

KM-1301SRJ

18,900 BTU/hr

KM-1301SRJ3

18,800 BTU/hr

NOTICE

Allow 24" (61 cm) clearance
at front and rear for proper
air circulation and ease of
maintenance and/or service
should they be required.

5. Remote Condenser Unit URC-14FZ (use with KM-1301SRJZ/3)

6. Remote Condenser Unit URC-22FZ (use with KM-1601SRJZ/3, KM-1900SRJZ/3,

KM-2200SRJZ3) and URC-26JZ (use with KM-2600SRJZ3)

Icemaker
Model

URC Model

Heat of Rejection

AT 90°F (32°C)
WT 70°F (21°C)

KM-1601SRJZ

URC-22FZ 21,000 BTU/hr

KM-1601SRJZ3 URC-22FZ 26,400 BTU/hr
KM-1900SRJZ URC-22FZ 26,500 BTU/hr
KM-1900SRJZ3 URC-22FZ 25,700 BTU/hr
KM-2200SRJZ3 URC-22FZ 30,800 BTU/hr
KM-2600SRJZ3 URC-26JZ 40,600 BTU/hr

NOTICE

Allow 24" (61 cm) clearance
at front and rear for proper
air circulation and ease of
maintenance and/or service
should they be required.

Units: mm [in.]

295
[11.6]

80
[3.15]

Rear

Top

«
...
13
14
15
16
17
...
»

Summary of Contents for KM-1301SRJZ














































Reviews:

No comments