Metal Hose Reel Cart
User Manual
MODEL: 3557-CH - 3558-CH
youtube.com
/hoselink
Cultivating
Connections
INSTALL CRANK AND WATER INLET
STEP FIVE:
•
Push the crank handle into the slot on the right-hand side
of the cart (figure 4).
•
Secure in place using the screw provided.
•
Install the water inlet (figure 5) by pulling the locking
lever (figure 6) down and inserting the water inlet in the
desired orientation.
•
Make sure the inlet tube is pushed all the way in before
closing the locking lever to secure.
INSTALLING THE HOSE ON THE HOSE CART
STEP SIX:
•
Thread hose through the feeder.
•
Slide hose clamp over the end of the hose.
•
Submerge end of hose into boiling water to soften, then
push hose onto water inlet stem.
•
Tighten hose clamp with Phillips head screwdriver.
NOTE:
Hose guide can easily be aligned by rolling the feeder wheel
into the correct position, which is on the far left-hand side.
OPERATION
Step 1:
If not already attached, screw on the included Hoselink
Universal Tap Connector with black reducer to the water
inlet on the left side of the Hose Reel Cart. Attach the
other Tap Connector to your outdoor tap. Attach the
leader hose to both Tap Connectors.
Step 2:
Remove the length of hose needed from the drum.
Step 3:
Turn water on at the tap.
Step 4:
Use hose for watering.
Step 5:
Before rewinding the hose, turn water off and squeeze
nozzle for a few seconds to release pressure in the hose.
Step 6:
Rewind hose. It is helpful to hold cart in place with one
foot while cranking.
MAINTENANCE
Annual seal lubrication:
To prevent leaks and to lengthen seal life, the water inlet seals
should be lubricated annually.
•
Stop the flow of water to the unit by turning off the tap.
•
Release locking lever.
•
Pull the inlet tube from the axle.
•
Lubricate the seals. Silicone-based lubricant is recommended.
•
Replace the inlet tube, making sure it is pushed all the way in,
before closing the locking lever.
STORAGE
•
Turn water off when not in use.
•
Store the Hose Reel Cart indoors when you don’t intend to use
it for extended periods.
•
To prevent damage from expanding ice, always disconnect
and drain all hoses prior to frost and freezing conditions.
•
Clean the hose using only mild soap and water.
Connect the leader hose to the tap and then
connect onto the hose cart using the twist and lock action
for the Hoselink fittings.
Remove length of hose needed from drum.
Turn water on at tap.
Use hose for watering.
Before rewinding hose, bring the nozzle back to
cart, turn water off and squeeze nozzle for a few seconds to
release pressure in the hose.
Rewind hose. It is helpful to hold cart in place with
one foot while cranking.
Annual Seal Lubrication
To prevent leaks and to lengthen seal life, the water inlet
seals should be lubricated annually. Reference Figure 1.
Stop the flow of water to the unit by turning off the
tap.
Release locking lever. Reference Figure 2.
Pull the inlet tube from the axle.
Lubricate the seals as indicated. Silicone based
lubricant is recommended.
Replace the inlet tube making sure it is pushed all the
way in before closing the locking lever.
Turn water off when not in use.
Store the item indoors when you don’t intend to use it
for extended periods.
To prevent damage from expanding ice, always
disconnect and drain all hoses prior to frost and
freezing conditions.
Clean the hose using only mild soap and water.
Push the crank handle into the slot on the right hand
side of the cart.
Secure in place using the screw provided.
Install water inlet by pulling the locking lever down and
inserting the water inlet in the desired orientation.
Make sure the inlet tube is pushed all the way in
before closing the locking lever.
Thread hose through the feeder.
Slide hose clamp over the end of the hose
Submerge end of hose into boiling water to soften then
push hose onto stem.
Tighten hose clamp with Phillips head
NOTE: Hose guide can easily be aligned by rolling the
feeder wheel into the correct position which is on the far
left hand side.
For more information visit
www.hoselink.com.au
3
| Models: 3357 / 3358
➜
Connect the leader hose to the tap and then
connect onto the hose cart using the twist and lock action
for the Hoselink fittings.
Remove length of hose needed from drum.
Turn water on at tap.
Use hose for watering.
Before rewinding hose, bring the nozzle back to
cart, turn water off and squeeze nozzle for a few seconds to
release pressure in the hose.
Rewind hose. It is helpful to hold cart in place with
one foot while cranking.
Annual Seal Lubrication
To prevent leaks and to lengthen seal life, the water inlet
seals should be lubricated annually. Reference Figure 1.
Stop the flow of water to the unit by turning off the
tap.
Release locking lever. Reference Figure 2.
Pull the inlet tube from the axle.
Lubricate the seals as indicated. Silicone based
lubricant is recommended.
Replace the inlet tube making sure it is pushed all the
way in before closing the locking lever.
Turn water off when not in use.
Store the item indoors when you don’t intend to use it
for extended periods.
To prevent damage from expanding ice, always
disconnect and drain all hoses prior to frost and
freezing conditions.
Clean the hose using only mild soap and water.
Push the crank handle into the slot on the right hand
side of the cart.
Secure in place using the screw provided.
Install water inlet by pulling the locking lever down and
inserting the water inlet in the desired orientation.
Make sure the inlet tube is pushed all the way in
before closing the locking lever.
Thread hose through the feeder.
Slide hose clamp over the end of the hose
Submerge end of hose into boiling water to soften then
push hose onto stem.
Tighten hose clamp with Phillips head
NOTE: Hose guide can easily be aligned by rolling the
feeder wheel into the correct position which is on the far
left hand side.
For more information visit
www.hoselink.com.au
3
| Models: 3357 / 3358
Figure 5
Figure 4
Figure 6
