background image

5

©   2 0 0 2   d i r e c t e d   e l e c t r o n i c s ,   i n c .

1. Never operate the system in an enclosed or partially

enclosed area without ventilation (such as a garage). 

2. When parking in an enclosed or partially enclosed area

or when having the vehicle serviced, the remote start

system must be disabled using the toggle switch. 

3. It is the user's sole responsibility to properly handle and

keep out of reach from children all remote control trans-

mitters to assure that the system does not unintention-

ally remote start the vehicle. 

4. THE USER MUST INSTALL A CARBON

MONOXIDE DETECTOR IN OR ABOUT THE

LIVING AREA ADJACENT TO THE VEHICLE.

ALL DOORS LEADING FROM ADJACENT

LIVING AREAS TO THE ENCLOSED OR

PARTIALLY ENCLOSED VEHICLE STORAGE

AREA MUST AT ALL TIMES REMAIN CLOSED.

Use of this product in a manner contrary to its intended

mode of operation may result in property damage, personal

injury, or death. Except when performing the Safety Check

outlined in this user’s guide, (1) Never remotely start the

vehicle with the vehicle in gear, and (2) Never remotely start

the vehicle with the keys in the ignition. The user will be

responsible for having the neutral safety feature of the vehicle

periodically checked, wherein the vehicle must not remotely

start while the car is in gear. This testing should be performed

by an authorized Directed dealer in accordance with the

Safety Check outlined in this product installation guide. If

Summary of Contents for 851T


















































Reviews: