Hornet 851T User Manual Download | Manualshive

Page: 7 / 49

background image

4

© 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c .

your warranty

Your warranty registration must be completely filled out and

returned within 10 days of purchase. Your product warranty

will not be validated if your warranty registration is not returned.

Please note that it is necessary to keep your proof of purchase.

fcc/id notice

This device complies with Part 15 of FCC rules. Operation is

subject to the following conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

w

wa

arrn

niin

ng

g!! ssa

affe

ettyy ffiirrsstt

The following safety warnings must be observed at all times:

➤

When properly installed, this system can start the vehicle via
a command signal from the remote control transmitter.
Therefore, never operate the system in an area that does not
have adequate ventilation. The following precautions are the
sole responsibility of the user; however, the following recom-
mendations should be made to all users of this system:

➜

➜

«
...
5
6
7
8
9
...
»

Summary of Contents for 851T


















































Reviews:

No comments

Related manuals for 851T

Brand: WISEUP SHOP Pages: 90

Brand: TFA Pages: 2

Brand: SkyScan Pages: 7

Brand: Geemarc Pages: 2

Brand: Geemarc Pages: 2

Brand: Rattler Pages: 22

Brand: Red Smoke Alarms Pages: 2

Brand: Datexx Pages: 1

Brand: ELTRA Pages: 4

Brand: SenTech Pages: 2

Brand: Spamel Pages: 5

Brand: Quell Pages: 19

Brand: Valet Pages: 43

Brand: Oregon Scientific Pages: 23

OL-AL(MIB)-FM2-E

Brand: Omega Link Pages: 15

Excalibur Gold ATV Series

Brand: Omega Research & Development Pages: 81

Brand: SANJIANG Pages: 4

Brand: Omega Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands