manualshive.com logo in svg

Hornet 553T, Installation Manual

The Hornet 553T Installation Manual is a comprehensive guide designed to assist users in installing and setting up the Hornet 553T security system effortlessly. Easily accessible for free download at manualshive.com, this manual provides step-by-step instructions and valuable information on configuring your system for optimal performance.

Share
Download
background image

© 2000 Directed Electronics, Inc. Vista, CA

3

what is included

table of contents

What is Included

. . . . . . . . . . . . . . . . . . . . . . . . . 3

Warning! Safety First

. . . . . . . . . . . . . . . . . . . . . . 4

Installation Points to Remember

. . . . . . . . . . . . . . 5

Before Beginning the Installation . . . . . . . . . . . 5
After the Installation. . . . . . . . . . . . . . . . . . . . 5

Deciding on Component Locations

. . . . . . . . . . . . . 6

Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control Module . . . . . . . . . . . . . . . . . . . . . . . . 6
Shock Sensor . . . . . . . . . . . . . . . . . . . . . . . . . 7
Valet/Program Switch . . . . . . . . . . . . . . . . . . . 8
Status LED. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Optional Starter Kill Relay . . . . . . . . . . . . . . . . 9
Relay Satellite . . . . . . . . . . . . . . . . . . . . . . . . 9

Finding the Wires You Need

. . . . . . . . . . . . . . . . . 9

Obtaining Constant 12V . . . . . . . . . . . . . . . . . . 9
Finding the 12V Switched Ignition Wire . . . . . . . 10
Finding the Starter Wire . . . . . . . . . . . . . . . . . 10
Finding the Accessory Wire . . . . . . . . . . . . . . . 11
Finding the Tachometer Wire . . . . . . . . . . . . . . 11
Finding the Wait-to-Start Wire for Diesels. . . . . . 11
Finding the Parking Light Wire . . . . . . . . . . . . . 12
Finding the Door Pinswitch Circuit . . . . . . . . . . 12

Making Your Wire Connections

. . . . . . . . . . . . . . . 13

Primary Harness (H1), 12-Pin Connector

. . . . . . . . 14

Secondary Harness (H2), 3-Pin Connector 

. . . . . . 14

Remote Start Primary Harness, 5-Pin Connector

. . . 15

Heavy Gauge Relay Satellite 

. . . . . . . . . . . . . . . . 15

Remote Start Secondary Harness (H3), 6-Pin Connector

. 15

Primary Harness (H1) Wire Connection Guide

. . . . 16

Secondary Harness (H2) Wire Connection Guide

. . . . 20

Relay Satellite Key Switch Interface Wire

Connection Guide

. . . . . . . . . . . . . . . . . . . . 22

Remote Start Harness (H3) Wire Connection Guide

. 23

Neutral Safety Switch Interface

. . . . . . . . . . . . . . 25

Testing the Neutral Safety Switch . . . . . . . . . . . 25

Bypassing GM Vehicle Anti-Theft Systems (VATS)

. . . . 28

1995 and Newer Vehicle Anti-Theft Systems

(Immobilizers)

. . . . . . . . . . . . . . . . . . . . . . . . . 29

Plug-In LED and Valet/Program Switch

. . . . . . . . . 30

Programmer Interface, 3-Pin Black Connector

. . . . 30

Shock Sensor Harness, 4-Pin Connector

. . . . . . . . . 31

Tach Learning

. . . . . . . . . . . . . . . . . . . . . . . . . . 32

Door Lock Harness (H4) Wire Connection Guide

. . . . 32

Type A: Positive-Triggered, Relay Driven Systems . 33
Type B: Negative-Triggered, Relay Driven Systems . 34
Type C: Reversing Polarity System . . . . . . . . . . . 34
Type D: Adding One or More After-Market Actuators . 35
Type E: Electrically Activated Vacuum . . . . . . . . 36
Type E: One-Wire System. . . . . . . . . . . . . . . . . 36
Type G: Positive (+) Multiplex . . . . . . . . . . . . . 37
Type H: Negative (-) Multiplex . . . . . . . . . . . . . 38

Programming Jumpers

. . . . . . . . . . . . . . . . . . . . 39

Tach Threshold On/Off . . . . . . . . . . . . . . . . . . 39
Light Flash (+)/(-). . . . . . . . . . . . . . . . . . . . . 39

Transmitter/Receiver Learn Routine

. . . . . . . . . . . 40

Transmitter Configurations

. . . . . . . . . . . . . . . . . 42

Standard Configuration . . . . . . . . . . . . . . . . . . 42
Single Button Arm/Disarm Configuration . . . . . . 42

Multi-Level Security Arming

. . . . . . . . . . . . . . . . 43

Operating Settings Learn Routine

. . . . . . . . . . . . 44

Feature Menus

. . . . . . . . . . . . . . . . . . . . . . . . . . 46

Feature Descriptions

. . . . . . . . . . . . . . . . . . . . . 47

Nuisance Prevention Circuitry

. . . . . . . . . . . . . . . 51

Valet Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Timer Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Table of Zones

. . . . . . . . . . . . . . . . . . . . . . . . . . 53

Shutdown Diagnostics

. . . . . . . . . . . . . . . . . . . . 53

Long Term Event History

. . . . . . . . . . . . . . . . . . . 54

Safety Check

. . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . 56

Alarm Troubleshooting . . . . . . . . . . . . . . . . . . 56
Remote Start Troubleshooting . . . . . . . . . . . . . 56

Wiring Quick Reference Guide

. . . . . . . . . . . . . . . 60

■

The control module

■

An HF Plus receiver/antenna

■

Two remote transmitters P/N 476H

■

A Stinger Doubleguard shock sensor

■

A Revenger Soft Chirp siren

■

The plug-in status LED

■

The plug-in Valet/Program switch

■

A hood pinswitch

■

A relay satellite

■

A toggle (override) switch

Summary of Contents for 553T





























































Reviews:

No comments

Related manuals for 553T

2N NetSpeaker Quick Start Manual preview
NetSpeaker
Brand: 2N Pages: 23
2seeU 2CU-Z301-AHD Operating Instruction preview
2CU-Z301-AHD
Brand: 2seeU Pages: 2
JBL SONNET Owner'S Manual preview
SONNET
Brand: JBL Pages: 2
JBL Simply Cinema ESC333 Simple Setup Manual preview
Simply Cinema ESC333
Brand: JBL Pages: 16
JBL Project K2.S5500 Technical Manual preview
Project K2.S5500
Brand: JBL Pages: 2
JBL LS Series Brochure & Specs preview
LS Series
Brand: JBL Pages: 8
Panasonic 4350 Quick Start Manual preview
4350
Brand: Panasonic Pages: 2
JBL CM40 Technical Manual preview
CM40
Brand: JBL Pages: 2
JBL Authentics L 16 Quick Start Manual preview
Authentics L 16
Brand: JBL Pages: 11
Nelson NS-40 Instruction And Maintenance Manual preview
NS-40
Brand: Nelson Pages: 18
Nelson N1500i Operation And Service Manual preview
N1500i
Brand: Nelson Pages: 150
NELLYS SECURITY F SERIES Quick Start Manual preview
F SERIES
Brand: NELLYS SECURITY Pages: 15
Oase Water Jet Lightning Warranty, Safety And Operating Instructions preview
Water Jet Lightning
Brand: Oase Pages: 28
Oase SwimSkim 25 Operating Instructions Manual preview
SwimSkim 25
Brand: Oase Pages: 9
V-TAC VT-5122 Installation Instruction preview
VT-5122
Brand: V-TAC Pages: 97
V-TAC 80133970 Installation Instructions Manual preview
80133970
Brand: V-TAC Pages: 14
Yamaha YAS-306 Owner'S Manual preview
YAS-306
Brand: Yamaha Pages: 40
Yamaha YAS-109 Update Manual preview
YAS-109
Brand: Yamaha Pages: 8

Brands by name

Popular brands

Load more brands