manualshive.com logo in svg

Hornet 553T, Installation Manual

Share
Download
Hornet 553T Installation Manual Download Page 17

© 2000 Directed Electronics, Inc. Vista, CA

17

A momentary input on this wire will start or stop the motor, just as transmitting Channel 3 from the remote trans-

mitter does. It is often connected to an optional momentary push-button switch to make access to Valet Take

Over Mode and Timer Mode more convenient. 

Connect this wire to the optional domelight supervision relay as shown below:

IMPORTANT! 

This output is only intended to drive a relay. It cannot be connected directly to the

domelight circuit, as the output cannot support the current draw of one or more light bulbs. 

Most vehicles use negative door trigger circuits. Connect the green wire to a wire which shows ground when any

door is opened. In vehicles with factory delays on the domelight circuit, there is usually a wire that is unaffected

by the delay circuitry. This wire will report Zone 3.

H1/5 GREEN (-) door trigger input, zone 3

H1/4 BLACK/WHITE (-) 200 mA domelight supervision output

H1/3 WHITE/BLUE remote start (-) activation input

Summary of Contents for 553T





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands