manualshive.com logo in svg

HORNER EXLW PRIME Series, User Manual

The HORNER EXLW PRIME Series User Manual is an essential guide for operating this advanced product. Designed for easy understanding, this comprehensive manual is available for free download on our website. Explore the limitless possibilities of the HORNER EXLW PRIME Series and download the manual today at manualshive.com.

Share
Download
background image

 

 

MAN1256-05-EN_EXLW_XLWP_UM 

November 10, 2021 

 

 

 

 

31 | 201 

 

5.4  View Status 

 

 

 
 
The View Status Sub-Menu displays up to 19 System Settings. Only the OCS Mode System Setting is 
editable. 
 

Model 

XW1yz= Model number of this EXLW/XLW PRIME OCS unit 
1yz = indicates the installed I/O module 
00 = no I/O module 

OCS Mode 

Idle = EXLW/XLW PRIME OCS is in Idle mode 
DoIO = EXLW/XLW PRIME OCS is in Do I/O mode 
Run = EXLW/XLW PRIME OCS is in Run mode 

Scan Rate(mS) 

0.0 = EXLW/XLW PRIME OCS is not in Run mode 
0.1 to 999.9= Average number of mS for each ladder scan 

OCS Net Use % 

0.0 to 100.0 = CAN network bandwidth % used by this EXLW/XLW 
PRIME OCS node 

All Net Use % 

0.0 to 100.0 = CAN network bandwidth % used by all nodes 

Ladder Size 

x = Number of bytes in application ladder program 

Config Size 

x = Number of bytes in application I/O configuration 

Graphics Size 

x = Number of bytes in application graphic screens 

String Size 

x = Number of bytes in application string table 

Bitmap Size 

x = Number of bytes in application bitmaps  

Text Tbl Size 

x = Number of bytes in application text tables 

Font Tbl Size 

x = Number of bytes in application font tables 

Protocol Size 

x = Number of bytes in application downloaded protocols 

SMS File Size 

x = Number of bytes in application SMS protocol configuration 

Firmware Rev 

xx.yy = Current firmware version 

OS Ver 

a.b.cd.yz = Current Operating System version 

FPGA Rev 

x.y = Current FPGA version (High Speed IO Sub System) 

InitRD Rev 

x.yz = Bootloader version 

Self-Test 

Ok = All power-on self-tests passed 
Fault = One or more power-on self-tests failed 

 

 

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Radio Shack 4 Owner'S Manual preview
4
Brand: Radio Shack Pages: 52
Samson 430 Series Mounting And Operating Instructions preview
430 Series
Brand: Samson Pages: 78
Rachio 3 Get Started preview
3
Brand: Rachio Pages: 16
D-Link DSN-640 Quick Installation Manual preview
DSN-640
Brand: D-Link Pages: 40
ZETRON MAX Connection Manual preview
MAX
Brand: ZETRON Pages: 3
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Brand: Yamaha Pages: 92
Parker P33 Integration Manual preview
P33
Brand: Parker Pages: 54
RAM RP2000 User Manual preview
RP2000
Brand: RAM Pages: 71
hager ZZ45WAN2PP Mounting Instructions preview
ZZ45WAN2PP
Brand: hager Pages: 2
hager TYB601A Quick Start Manual preview
TYB601A
Brand: hager Pages: 4
National Instruments SCXI -1122 Calibration Procedure preview
SCXI -1122
Brand: National Instruments Pages: 17
Davey Torrium 2 TT45 Installation And Operating Instructions Manual preview
Torrium 2 TT45
Brand: Davey Pages: 12
V2 WES-EASY Manual preview
WES-EASY
Brand: V2 Pages: 48
Measurement Computing CIO-DAS1401/12 User Manual preview
CIO-DAS1401/12
Brand: Measurement Computing Pages: 32
GEM DG-2000 Series Operation Manual preview
DG-2000 Series
Brand: GEM Pages: 17
Fagor 8040 CNC - FEATURES Manual preview
8040 CNC - FEATURES
Brand: Fagor Pages: 247
ADLINK Technology PCIe-8332 User Manual preview
PCIe-8332
Brand: ADLINK Technology Pages: 37
Wieland Samos Pro Compact SP-COP2 Instruction Manual preview
Samos Pro Compact SP-COP2
Brand: Wieland Pages: 36

Brands by name

Popular brands

Load more brands