background image

EN

Pulse

 15e

Safety Precautions and Warnings

14+

AGE RECOMMENDATION:

 

Not for children under 14 
years. This is not a toy. 

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.  For up-to-date product  literature, 
visit www.forcerc.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING

: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high 

probability of superfi cial injury.

CAUTION

: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE

: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

WARNING

: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product 

correctly can result in damage to the product, personal property and cause serious injury. 

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this 
Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without 
direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. 
This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to 
assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

As the user of this product, you are solely responsible for operating in a manner 
that does not endanger yourself and others or result in damage to the product or 
the property of others.

•  Always keep a safe distance in all directions around your model to avoid 

collisions or injury. This model is controlled by a radio signal subject to 
interference from many sources outside your control. Interference can cause 
momentary loss of control.

•  Always operate your model in open spaces away from full-size vehicles, traffi c 

and people.

•  Always carefully follow the directions and warnings for this and any optional 

support equipment (chargers, rechargeable battery packs, etc.).

•  Always keep all chemicals, small parts and anything electrical out of the reach 

of children.

•   Always avoid water exposure to all equipment not specifi cally designed and 

protected for this purpose. Moisture causes damage to electronics.

•   Never place any portion of the model in your mouth as it could cause serious 

injury or even death.

•   Never operate your model with low transmitter batteries.
•  Always keep aircraft in sight and under control.
•  Always use fully charged batteries.
•  Always keep transmitter powered on while aircraft is powered.
•  Always remove batteries before disassembly.
•  Always keep moving parts clean.
•  Always keep parts dry.
•  Always let parts cool after use before touching.
•  Always remove batteries after use.
•  Always ensure failsafe is properly set before fl ying.
•  Never operate aircraft with damaged wiring.
•  Never touch moving parts.

2

Summary of Contents for Pulse 15e





































Reviews: