5
EN
LMT SOLID AXLE 4WD MONSTER TRUCK • RTR: INSTRUCTION MANUAL
DRIVING PRECAUTIONS
• Maintain sight of the vehicle at all times.
• Routinely inspect the vehicle for loose wheel hardware.
• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle off-road
can cause fasteners to loosen over time.
• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.
CAUTION:
Do not discharge a Li-Po battery below 3V per cell. Batteries discharged
to a voltage lower than the lowest approved voltage may become damaged,
resulting in loss of performance and potential fire when batteries are charged.
• Do not apply forward or reverse throttle if the vehicle is stuck.
Applying throttle in this instance can damage the motor or ESC.
• After driving the vehicle, allow the electronics to cool before driving the vehicle again.
IMPORTANT:
Keep wires away from all moving parts.
POWERING ON THE VEHICLE
1. Center the ST TRIM and TH TRIM dials on the transmitter and turn it on.
2. Install a fully charged battery pack per the
Installing the Battery
section.
3. Power on the ESC.
BEFORE RUNNING YOUR VEHICLE
1. Check for free suspension movement. All suspension arms and steering components should
move freely. Any binds will cause the vehicle to handle poorly.
TIP:
To increase the ride height and ground clearance of your vehicle, screw down the
shock collars to compress the springs.
2. Charge a battery pack. Always charge the battery pack as per the battery and/or charger
manufacturers’ instructions.
3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim so
that the vehicle drives straight with no input to the steering.
4. Perform a Control Direction Test.
1. Press and hold the bind button, and
Power ON the receiver; the orange
LED will begin to flash.
2. Set the trims and control positions
at the desired failsafe settings,
press and hold the bind button,
and power ON the DX3 Smart
transmitter.
3. When the orange LED on the DX3
Smart transmitter remains lit, it is
connected to SR315 receiver.
You must rebind when:
• Different failsafe positions are desired e.g., when throttle or steering reversing has been changed.
• Binding the receiver to a different transmitter.
Bind Button
WARNING:
Do not kink, cut or damage the antenna wire. The antenna is made of
a coaxial wire; if the outer sheath becomes damaged, the receiver will not work
properly. If the antenna is damaged in any way, replace the antenna before attempting to
use the receiver.
SR315 RECEIVER
BINDING THE RECEIVER
Binding is the process of programming the receiver to recognize the GUID (Globally Unique
Identifier) code of a single specific transmitter. In the event of a loss of signal the receiver will
default the servo outputs to the failsafe position. The failsafe positions are set during binding;
Leave the throttle and steering at the neutral positions during binding.
Specifications
Type:
Dual Protocol 3 Ch Receiver (SLT/DSMR)
Dimensions (LxWxH):
32.5 x 21.5 x 12.4mm
Antenna Length:
90mm
Channels:
3
Weight:
6g
Band:
2.4GHz
Voltage Range:
3.5–9.6V
Bind Type: Bind Button
Failsafe:
Hold the steering wheel and throttle trigger in the
desired failsafe positions during binding
STR THR
BATT
AUX 1
RECEIVER ANTENNA
The SR315 receivers feature a coaxial antenna design for easy installation in almost any model.
Think of the last 1 inch (32mm) on the tip of the antenna as the active portion of the antenna,
the coaxial portion leading up to it is just an extension. Install the antenna so the active portion is
positioned as high as possible in the vehicle, and not “in the shadow” of any carbon fiber or metal.
The case of the receiver can accept an antenna tube directly, making optimal antenna placement
easy (antenna tube not included).
This transmitter requires 4 AA batteries
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION:
Never remove the transmitter batteries while the
model is powered ON. Loss of model control, damage, or injury may
occur.
CAUTION:
If using rechargeable batteries, charge only
rechargeable batteries. Charging non-rechargeable batteries may
cause the batteries to burst, resulting in injury to persons and/or damage
to property.
CAUTION:
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to national regulations.
TRANSMITTER BATTERY INSTALLATION
