Horizon Hobby EFLU6550 Instruction Manual Download Page 14

Page: 14 / 20

Post Flight Checklist



1. Disconnect the flight battery from the ESC

(Required for safety and battery life).

2. Power OFF the transmitter.
3. Remove the flight battery from the

aircraft.

4. Recharge the flight battery.



5. Store the flight battery apart from the

aircraft and monitor the battery charge.

6. Make note of the flight conditions and flight

plan results, planning for future flights.

Replacement Parts

Optional Items

Recommended Items

Part #

Description

EFLDF30R

6-Blade Rotor, 30mm

EFLU6551

Pushrod Set

EFLU6552

Landing Gear

EFLU6553

Hatch/Canopy

EFLU6554

Fuselage w/nose cone and Nacelle

EFLU6555

Nacelle Set

EFLU6556

Wing

EFLU6557

Tail Set

EFLU6558

Ducted Fan Unit

EFLU6559

Decal Sheet

EFLUM0810

8,800Kv Brushless Outrunner

SPMA3182

Integrated Rx

SPMSA2030L

2.3 g Linear Long Throw Servo

Part #

Description

SPMR6775

NX6 6 Ch DSMX Transmitter Only

SPMR8100

DX8e 8 Ch Transmitter Only

SPMR8200

NX8 8 Ch DSMX Transmitter Only

SPMXBC100

Smart Battery & Servo Tester

SPMXCA322

Adapter: IC2 Battery - JST-RCY Device

Part #

Description

DYN1400

LiPo Charge Protection Bag,Small

SPMR6655

DX6e 6 Ch Transmitter Only

SPMX8503S30

850mAh 3S Smart G2 30C; IC2

SPMXC1070

Smart S150 AC/DC Charger, 1x50W

SPMXC1080

Smart S1100 AC Charger, 1x100W

SPMXCA320

Adapter: IC3 Batt / IC2 Device

Summary of Contents for EFLU6550





















Search results

Summary of Contents for EFLU6550

Reviews:

Related manuals for EFLU6550

Brands by name

Popular brands

Horizon Hobby EFLU6550, Instruction Manual

Search results

Summary of Contents for EFLU6550

Reviews:

Related manuals for EFLU6550

Brands by name

Popular brands