Horizon Hobby Blade 700X Instruction Manual Download Page 4

Page: 4 / 32

Assembly Guide Legend

Tools Needed To Complete

Required Items

Optional Items

OIL

• 1.5mm, 2mm, 2.5mm, 3mm and 4mm hex drivers
• Ball link pliers
• Needle nose pliers
• Phillips screwdriver
• Wire cutter

• Pitch gauge
• Metric calipers
• Petroleum-based, light viscosity lube
• Medium cyanoacrylate (CA)

• 3 Servos

(3) H6200 servos (SPMSH6200)
included with combo BLH5725C

• Receiver/Flybarless control unit

AR7200BX (SPMAR7200BX)
included with combo BLH5725C

•

DSMX Remote Receiver (SPM9645)
included with combo BLH5725C

• 1 Tail servo

(1) H6210 servo (SPMSH6210)
included with combo BLH5725C

• E-ﬂ ite 200W charger

(EFLC3020)

• E-ﬂ ite

EC5 Battery Series

Harness, 10 AWG (EFLAEC508)

• Dynamite

Li-Po Charge

Protection Bag, Large
(DYN1405)

• Revolution

Ball Link

Tool (RVO1009)

• Revolution Deluxe Ball

Link Pliers (RVO1005)

• Control Rod Set Up Tool

(RVO1004)

• Revolution Low-Bounce

Rubber Work Mat
(RVO1020)

• Revolution Hex Driver

Set, 1.5/2.0/2.5/3.0mm
(RVO2000)

• Revolution 2.5mm Op-

tion Extended Hex Tip
(RVO2012)

• Celectra™ 15VDC 250W

Power Supply (EFLC4010)

• DSM2

/DSMX

compatible DX6i 6 channel

transmitter or higher

• (2X) 5000mAh 6S 22.2V 30C Li-Po,

10AWG with EC5™ connector
(EFLB50006S30)

• E-ﬂ ite EC5 Device Charge

Lead with 6” Wire & Jacks,
12 AWG and EC5 connector
(EFLAEC512)

Apply Petroleum-Based,
Light Viscosity Lube

Apply Synthetic Grease

Apply MEDIUM CA

Apply NO Threadlock

Apply BLUE Threadlock

Loosely Tighten

Fully Tighten

Repeat Multiple Times

Summary of Contents for Blade 700X

































Search results

Summary of Contents for Blade 700X

Reviews:

Related manuals for Blade 700X

Brands by name

Popular brands

Horizon Hobby Blade 700X, Instruction Manual

Search results

Summary of Contents for Blade 700X

Reviews:

Related manuals for Blade 700X

Brands by name

Popular brands