Horizon Hobby .40NX Evolution User Manual Download Page 8

7

Recommended propellers:

Break in*

  9 x 6, 10 x 6

Sport

  9 x 6, 9 x 7
  10 x 6, 11 x 5

Performance (tuned exhaust)

  9 x 6, 9 x 7, ( Prop the engine to achieve over 15,000  
  rpm on the ground)
* 2-blade propellers

Attaching the Propeller and Spinner

Remove the prop nut and prop washer from the engine. 
Install the spinner backplate. Install the propeller, the 
prop washer and then the prop nut in that order (see 
photo). Securely tighten the prop nut using an adjustable 
wrench. Install the spinner cone.

Starting the Evolution Engine

Fuel

We recommend using high-quality Cool Power Omega, 
Hangar 9

®

 AeroBlend

 or Power Master fuels containing 

10 to 15% nitro. The Evolution Engine has been test-run 
using these fuels. If another brand of fuel is used, it 
may be necessary to slightly adjust the needle valves to 
compensate for the differences in fuel.

Glow Plug

The Evolution engine comes with a specially designed 
“Super Plug” that prevents idle and transition flameouts. 
The plug’s unique shape directs the incoming fuel/air 
mixture away from the plug element. When replacing the 
plug, be sure to replace it with another Evolution 2- or 
4-cycle  Super Plug (EVOGP1).

Starting the Engine

Step 1.

   Fill the tank with the above-mentioned 10 or  

15% fuel.

Step 2.

   Reattach the fuel lines, making sure the vent 

and clunk line are attached to the fuel nipple 
and the muffler pressure nipple. 

NOTICE:

 Do not attach the glow driver yet.

Step 3.

  The high-speed needle valve should be turned 

open 2-turns from closed for the initial first start. 

Step 4.

   With the throttle fully open, place your thumb 

over the carburetor or the exhaust outlet of the 
muffler and flip the prop clockwise through 6 
complete revolutions, thus priming the engine.

Step 5.

   Close the throttle to the idle position and have a 

helper hold your airplane.

If you are planning to use a tuned exhaust system then 
we highly recommend the use of either of the following 
Hangar 9

®

 glow plugs.

HAN3015 #9 Performance Plug
HAN3020 #3 Performance Plug

Securely tighten the prop nut using a wrench.

Summary of Contents for .40NX Evolution

















Reviews: