hopf 8029HEPTA-V2/GPS Technical Manual Download Page 108

Page: 108 / 130

SSH

AND

ELNET

ASIC

ONFIGURATION

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

108 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

SSH and Telnet Basic Configuration

Only basic configuration is possible via SSH or Telnet. The complete
configuration of the Time Server 8029NTS/GPS takes place exclusively
via the WebGUI.

It is just as easy to use SSH (Port 22) or Telnet (Port 23) as the WebGUI. Both protocols use
the same user interface and menu structure.

The user names and passwords are the same as on the WebGUI and are kept in alignment
(see

Chapter 8.3.5.10 Passwords (Master/Device)

SSH does not allow blank passwords for safety reasons.

The corresponding protocols should be enabled for the use of Telnet or
SSH (see

Chapter 8.3.2.5 Management (Management-Protocols

–

HTTP,

SNMP)

The navigation through the menu takes place by entering the respective number associated
with the menu option (as can be seen in the above image).

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands