3
underneath the hose handle.
[1] (Depending on model)
Crevice Tool*
– For corners and hard to reach areas.
[12]
Furniture Nozzle*
– For soft furniture and fabrics
.[13]
Dusting brush* –
For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool.
[14]
Parquet Nozzle* –
For parquet floors and other delicate floors.
[1X]
Turbo Nozzle* –
Use the turbo nozzle for deep cleaning on carpets.
[1w]
Pet Hair Remover mini Turbo Nozzle* -
Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [1U]
Allergen Remover mini Turbo Nozzle* –
Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas, particularly suitable for allergen
removal.
[1V]
ImPORTANT:
Do not use the turbo and mini turbo nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while
brush is rotating.
ClEANER mAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator in the container empty the dust container.
ImPORTANT:
To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Release the container carry handle by lifting the centre latch to detach the dust
container from the main cleaner and pull upward to remove.
[15]
2. Hold the dust container over a bin with one hand and with the other pull the dust
container catch to open the door and empty.
[16]
3.
Close the dust container door and refit to the cleaner main body. To lock in place
push the container carry handle down until the latch connects with the main body
of the cleaner. Once correctly retained the carry handle will sits flush with the top
of the cleaner.
Cleaning the washable filters
The cleaner is fitted with a filter pack. To maintain optimum cleaning performance
regularly remove the the filters and tap against the side of the bin to release dust.The
filters should be washed every 3 months or when the filter has excessive dust level.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean
your filters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
ImPORTANT:
Regularly check and maintain the filters.
ImPORTANT:
Always ensure the filter pack is fully dry before use.
To access the Pre- Motor filter:
NOTE:
Ensure the carry handle is at its down position before opening the filter door.
1.
Unlock the filter door by pulling the filter latch upwards. Open the filter door. [17]
2.
Remove the blue filter pack by pressing down on the retainer catch to release. The
filter pack will pop up. Slide the filter pack out. [18]
3.
Unlatch the filter pack frame.
4.
Remove the micro filter from the pack frame and wash the micro filter by handusing
warm water. Do not use hot water or detergents. Remove excess water from the
filter and leave to dry fully before reusing. [21]
5.
Reassemble to filter pack once fully dry and refit to the cleaner. Press on the top of
the filter to ensure it clips back into place.
To access the exhaust filter:
1. Unlock the exhaust filter door by rotating the door along arrow indicated.
[19]
2. Remove the filter pack from recess.
[20]
3. Gently tap and wash the filter unit. Do not use hot water or detergents. Remove
excess water from the filter and leave to dry fully before reusing.
[21]
4. Reassemble filter pack once fully dry and refit to the cleaner.
ImPORTANT:
Do not use the product without the filter pack fitted.
Cleaning the Airvolution separation unit
This cleaner uses the Airvolution separation system, unique to Hoover. If necessary the
Airvolution separation unit can be removed from the dust container and cleaned.
1. Remove dust container from the cleaner by releasing the container carry handle to
detach the dust container from the main cleaner and pull upward to remove.
[15]
2.
Place the dust container on a flat surface and unclip the clips from either side of the
dust container.
[22]
3. Using the dust container handle lift the dust container upper section containing
theseparation unit from the lower section.
[23]
4. Use a cloth to remove excessive dust from the separation unit’s surface.
[24]
5. Reassemble the dust container upper section. Push clips back to fully close the dust
container.
[25]
6.
Refit the dust container to the cleaner. To lock in place push the container carry
handle down until the latch connects with the main body of the cleaner. Once
correctly retained the carry handle will sit flush with the top of the cleaner.
*Certain models Only
** Certain models only, nozzles may vary according to model
