background image

12

Lubrication

The motor is equipped with bearings that
contain sufficient lubrication for the life of
the motor.  The addition of lubricant
could cause damage.

Therefore, do

not add lubricant to motor bearings.

The agitator is equipped with two ball
bearings that should be lubricated peri-
odically by a Hoover Factory Service
Center or an Authorized Hoover Warranty
Service Dealer (Depot).

Thermal protector

An internal thermal protector has been
designed into your cleaner to protect it
from overheating.

When the thermal protector activates,
the cleaner will stop running.

If this

happens, proceed as follows:

1. Turn the cleaner OFF and discon-

nect it from the electrical outlet.

2. Check secondary and final filters

for dirt accumulation.

3. Refer to “Clearing blockages” sec-

tion. 

4. 

When cleaner is unplugged and

the motor cools for 30 minutes,

the 

thermal protector automatically resets
and cleaning may continue.

If the thermal protector continues to
activate after following the above steps,
your cleaner may need servicing (see
“Service” section).

3-22

3-24

3-23

E

Powered hand tool

Belt replacement

The powered hand tool belt is designed
to last a long time and is not normally
replaced. However, if the belt is crack-
ed, gouged or broken, it should be
replaced.

6. With curved ends down, slide end
plates (C) of brush roll into slots (E) on
tool.

7. Replace belt guard (B) making sure
not to pinch brush bristles in guard. Turn
agitator, making sure it rotates freely.

Replace and tighten screws.

8. To replace bottom plate (A), insert the
four tabs on edge of bottom plate into
slots on front of tool.

Pivot bottom plate down and snap
closed.

A

B

C

Replacing belt

When replacing belt, ask for 

HOOVER

part No. 38528037.

1. Remove bottom plate, belt guard and
brush roll as described in Figs. 3-19
through 3-21.

3-27

3-25

3-26

The belt can be seen through the top of
the nozzle or by removing the bottom
plate and belt guard (Figs. 3-19 and
3-20.

F

E

2. Grasp turbine (E) and pull firmly to
remove.

3. Remove belt from turbine pulley (F).
Replace with new belt.

4. With flat sides of turbine retainers (G)
pointing down, slide retainers into
grooves (H) in tool housing and snap
into place.

5. Replace brush roll, belt guard, and
bottom plate as described in Figs. 3-21
through 3-24.

G

H

Edge groomer
replacement

When to replace

The edge groomers, located on both
sides of the front of the cleaner, should
be replaced when they appear worn.

What to buy

When purchasing edge groomers, ask
for HOOVER 

part No. 39511004.

Replacing edge groomers

Disconnect cleaner from electrical
outlet.
Warning - Brush roll can start sud-
denly.  Unplug cleaner when it is
turned over.

Remove bottom plate as described in
Fig. 3-9.
Lift off both old edge groomers and slide
new edge groomers into position as
shown.
Reposition bottom plate and secure with
4 Phillips head screws (Fig. 3-13).

3-28

Summary of Contents for U6436-900 - TurboPower 7600 Self Propelled WindTunnel Upright

































Reviews: