background image

Y8150 FRESH AIR VENTILATION SYSTEM, W8150 FRESH AIR VENTILATION CONTROL

7

68-0282—07

Setting the control...

1.

Be sure power is turned on.

2.

Set the Ventilation Standard on the control.

3.

Set the bedrooms dial.

4.

Set the area (sq ft) dial.

5.

Set the airflow (cfm) dial.

6.

Press the test button and observe the lights:

Green light is flashing.

The dial settings meet the chosen standard.

Red light is flashing.

There is not enough fresh air delivered to meet the 

requirements of the selected standard. See 

Troubleshooting section.

7.

Record settings on the label inside the cover as shown 

in the diagram.

TIPS:

• Ventilation control reads new dial setting only when test 

button is pushed or power is cycled. To ensure dial settings 

are read, push test button after any changes are made.

• For single bedroom homes, set the bedrooms dial to 2 (this 

may result in more ventilation than the minimum required).

• For homes having more than five bedrooms and only a 

single ventilation system, set the bedrooms dial to 5 (this 

may result in less ventilation than the minimum required).

• For conditioned square feet, set area (sq ft) dial to the 

nearest value.

• For airflow, set airflow (cfm) dial to the nearest value.

• Vaulted ceilings do not need to be considered when setting 

this control.

• For homes with multiple systems: Honeywell recommends 

a ventilation control and fresh air intake for each system. 

Measure ventilation airflow for each system independently. 

Refer to Multi-system Setup Example for further details.

Customizing the ventilation control.

Honeywell
Golden Valley, MN 55422
50001159-001 Rev. A

W8150A 1001

1

www.honeywell.com/yourhome
or call 1-800-468-1502

_________

area (sq. ft.)

R

ecord  settings  above

Ventilation Limit*

Ventilation

Standard

1
2

60%

ASHRAE

 62.2

100%
62-1999

Installer

Test

M19991

    

 

Para 

español ver las instrucciones

*See Instructions 

Voir mode d'emploi en français inclus

R
C
DMP
DMP
AUX
AUX
REM
REM

24 VAC
XFRM

HVAC

Stat

Damper

ERV/Fan

Timer/Switch

G

F

R

C

C

C

C

H

W

G

T

Patent Pending

_________

bedrooms

_________

airflow (cfm)

Date installed:________________________

W8150A 1001

_________

area (sq. ft.)

Record settings above

Ventilation Limit*

Ventilation

Standard

1

2

60%

ASHRAE 62.2

100%

62-1999

Installer

Test

R
C
DMP
DMP
AUX
AUX
REM
REM

24 VAC
XFRM

HVAC

Stat

Damper

ERV/Fan

Timer/Switch

G

F

R

C

C

C

C

H

W

G

T

_________

bedrooms

_________

airflow (cfm)

Date installed:________________________

Summary of Contents for Y8150













Reviews: