manualshive.com logo in svg

Honeywell VX3Plus, Reference Manual, Page: 257 / 282

Share
Download
Honeywell VX3Plus Reference Manual Download Page 257

Certificates

Note:

Please refer to the Security Primer to prepare the Authentication Server and Access Point for

communication.

Note:

It is important that all dates are correct on the VX3Plus and host computers when using any type of

certificate. Certificates are date sensitive and if the date is not correct authentication will fail.

Quick Start

Root Certificates are necessary for EAP-TLS, PEAP/GTC and PEAP/MSCHAP.

1.

Generate a Root CA Certificate

and download it to a PC.

2. Connect the VX3Plus to the desktop PC using ActiveSync and copy the certificate to the VX3Plus \System folder.

3.

Install the Root CA Certificate

.

User Certificates are necessary for EAP-TLS

1.

Generate a User Certificate and Private Key file

and download it to a PC.

2. Connect the VX3Plus to the desktop PC using ActiveSync and copy the certificate and private key file to the VX3Plus

\System folder.

3.

Install the User Certificate and Private Key file

.

4. After installation, perform a Suspend/Resume.

5.

Verify installation

.

Generating a Root CA Certificate

Note:

It is important that all dates are correct on the VX3Plus and host computers when using any type of

certificate. Certificates are date sensitive and if the date is not correct authentication will fail.

The easiest way to get the root CA certificate is to use a browser on a PC to navigate to the Certificate Authority. To request
the root CA certificate, open a browser to

http://<CA IP address>/certsrv.

Sign into the CA with any valid username and password.

5-37

Summary of Contents for VX3Plus



























































































































































































































































































Reviews:

No comments