manualshive.com logo in svg

Honeywell VisionPRO TH8110U, Installation Instructions Manual, Page: 12 / 12

Share
Download
Honeywell VisionPRO TH8110U Installation Instructions Manual Download Page 12

69-1700    G.H.    03-04 

www.honeywell.com/yourhome

TH8110U TOUCH SCREEN PROGRAMMABLE THERMOSTATS

Automation and Control Solutions

Honeywell International Inc.

Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North

35 Dynamic Drive

Golden Valley, MN  55422

Scarborough, Ontario
M1V 4Z9

CAUTION

Equipment Damage Hazard.
Minimum compressor off-time is bypassed 
during Installer System Test.

Avoid cycling compressor quickly.

Table 7. System Test(s).

TROUBLESHOOTING (SEE TABLE 8)

Table 8. Troubleshooting.

Select

Installer 

Setup 

Number

Factory Setting

Other Choices

Comments

Options

Description

Options

Description

Installer Test 
Cool

Test 1

0

Cool is off

1

0

—cool off  

                                

1

—cool stage 1 

turns on

System selection deter-
mines tests available and 
number of stages shown.

Installer Test 
Fan

Test 2

0

Fan is off

1

0

—fan   off                                     

1

—fan turns on

Installer Test 
Heat

Test 3

0

Heat is off

1

0

—heat  off  

                                

1

—stage 1heat on

Symptom

Possible Cause

Action

Display does not come on.

Thermostat is not being 
powered.

Check for 24 Vac between C and Rc.
Verify AAA batteries installed correctly and good.

Temperature settings do not 
change.

The upper or lower 
temperature limits were 
reached.

Check temperature setpoints.
Check Installer Setup Numbers 0600 and 0610; 
modify.

The keypad is fully locked.

Check Installer Setup Number 0670 to change keypad 
lock options.

Heating or cooling does not 
come on.

Thermostat minimum off-
time is activated.

Wait up to five minutes for the system to respond.

System selection is not set to 
Heat or Cool.

Set system Selection to correct position.

O/B terminal is not set 
correctly (Heat Pumps only).

Check Installer Setup Number 0190 and set correctly.

System type Selection is 
incorrect.

Check Installer Setup Number 0170 and make sure 
correct System type is chosen.

Thermostat is calling for Heat 
(Heat on) or Cool (Cool on) but 
no heating or cooling is running.

Heating or cooling 
equipment is not operating.

Check wiring.
Check Installer Setup Number 0170; verify correct 
system type is chosen.
Verify equipment operation in System Test mode.

Thermostat does not respond 
when touchpad is pressed.

The keypad is locked.

Check Installer Setup Number 0670 to change keypad 
locked options.

Summary of Contents for VisionPRO TH8110U













Reviews:

No comments