manualshive.com logo in svg

Honeywell VisionPRO TH8110U, Installation Instructions Manual, Page: 11 / 12

Share
Download
Honeywell VisionPRO TH8110U Installation Instructions Manual Download Page 11

TH8110U TOUCH SCREEN PROGRAMMABLE THERMOSTATS

11

69-1700

SYSTEM CHECKOUT

Installer System Test

The Installer System Test mode is used to test the HVAC 
system(s). See Table 7. While in System Test mode, 
minimum off -time for compressors is bypassed. 

The Installer Test is part of Installer Setup options. Enter 
Installer Setup screen and press Down arrow key to bring 
up test selection(s) quickly. See Fig. 16.

ADVANCED FEATURES

Outdoor or Indoor Temperature Sensor

Allow outdoor or indoor temperature sensor to absorb the 
air for a minimum of five minutes before taking a reading. 
See the Sensor instructions for more information.

Keypad 
Lockout

0670

0

Unlocked keypad 1, 2

1

—partially locked      

keypad                                              

2

—fully locked keypad

Unlocked—all 
functions are 
available.
Partially locked—
only temperature up 
and down keys and 
ability to enter and 
modify Installer 
Setup mode are 
available.                                  
Fully locked—only 
ability to enter and 
modify Installer 
Setup mode are 
available.

Temperature 
Control in Heat

0680

2

Standard 
temperature 
control in heating

1, 3

1

—less aggressive 

temperature control 
(could cause 
temperature 
undershoot)                                                                           

3

—more aggressive 

temperature control 
(could cause 
temperature overshoot)

Applies to recovery 
ramp and use of 
auxiliary heat during 
recovery.

Choose 1 if getting 
temperature 
overshoot.

Choose 3 if getting 
temperature 
undershoot.

Temperature 
Control in Cool

0690

2

Standard 
temperature 
control in cooling

1, 3

1

—less aggressive 

temperature control 
(could cause 
temperature 
undershoot)                                                                           

3

—more aggressive 

temperature control 
(could cause 
temperature overshoot)

Applies to recovery 
ramp.

Choose 1 if getting 
temperature 
overshoot.

Choose 3 if getting 
temperature 
undershoot.

Temperature 
Display Offset

0700

0

No difference in 
displayed 
temperature and 
actual room 
temperature

 -3, -2, -1, 
0, 1, 2, 3

 -3

°

F (-1.5

°

C)                                                                                    

-2°F (-1°C)                                                                              
-1°F (-.5°C)                                                                               
0 F (0.°C)                                                                                 
1°F (.5°C)                                                                                
2°F (1°C)                                                                         
3°F (1.5°C)

 —

Reset 
Thermostat

0710

0

No thermostat 
reset.

1

Resets all Installer 
Setup Options to default 
values and resets 
schedule to default 
setting. 

Only calendar 
settings and time are 
retained.

Table 6. Advanced Settings Menu. (Continued)

Select

Installer 

Setup 

Number

Factory Setting

Other Choices

Comments

Option

Description

Options

Description

Summary of Contents for VisionPRO TH8110U













Reviews:

No comments