Vertex M
TM
24-Point Continuous Monitor
Section 5 - Maintenance
5-15
Note:
Some backup media may change the files to “read
only” and may require an additional step of chang-
ing the “Attributes” within the file properties to make
them usable.
Empty databases for the Event, Concentration and
ChemCam databases can be found in the Databases
folder on the Vertex M Technical Manual CD.
File Name
Purpose
Location
*.za_Vt
Configuration Profiles
C:\HMI\P_Util
CM72Data.dsn
ODBC Datasource for Event
Database
C:\HMI
ConcData.dsn
ODBC Datasource for
Concentration Database
C:\HMI
ChemCam.dsn
ODBC Datasource for
ChemCam Database
C:\HMI
CM72.mdb *
Event database
C:\HMI
CM72Conc.
mbd*
Concentration Database
C:\HMI
ChemCam.
mdb *
ChemCam Database
C:\HMI\
ChemCam
* Required if stored locally on the Vertex M System
NOTE: Database files are size limited to a maximum of 2Gb.
Table 5-2. File Locations
5.11 Optics Cleaning
Clean Chemcassette
®
optics annually or whenever
optics verification error occurs.
Required equipment:
• Compressed air
Note:
Do not use “canned air” near Pyrolyzer gas based
detectors, the halogenated gasses may trigger
alarms. Instead, use N
2
or a compressed source that
is free of oils and contaminants.
• Open the Optics Block Gate
• Remove the Chemcassette
®
• Open the Vertex M side panel
• Remove tubing (shown in photo) one at the
time and blow out with compressed air.
• Re-secure side panel and reload
Chemcassette
®
Note:
Remove and clean one port at a time to insure
proper orientation of tubing. Do not remove the capil-
lary tubing (microtubes).
CAUTION
Failure to replace and retighten hardware after service can
adversely affect monitor performance and electromagnetic
radiation compliance (EMC). Make certain all fasteners are
reinstalled and firmly fastened.
Remove these tubes one
at a time for cleaning
Summary of Contents for Vertex M
