background image

T8011R PROGRAMMABLE HEAT PUMP THERMOSTAT

68-0196–1

8

b.

Press Select.
Press 

 or 

 to set

Return temperature.

6.

Sleep

a.

Press Select.
Press 

 or 

 to set

Sleep time.

b.

Press Select.
Press 

 or 

 to set

Sleep temperature.

Setting the Weekend Program

7.

Wake

a.

Press Select.
Press 

 or 

 to set

Wake time.

b.

Press Select.
Press 

 or 

 to set

Wake temperature.

8.

Leave

a.

Press Select.
Press 

 or 

 to set

Leave time.

b.

Press Select.
Press 

 or 

 to set

Leave temperature.

9.

Return

a.

Press Select.
Press 

 or 

 to set

Return time.

b.

Press Select.
Press 

 or 

 to set

Return temperature.

10.

Sleep

a.

Press Select.
Press 

 or 

 to set

Sleep time.

b.

Press Select.
Press 

 or 

 to set

Sleep temperature.

11.

End Programming.
Press Select. End is
displayed. Programming is
complete. The thermostat
will revert to displaying the
current day, time and
temperature in five
seconds.

NOTE:

To reset the thermostat to the preprogrammed time
and temperature settings (see Table 1):
a.

Press and hold the Hold and Select keys
simultaneously. The display will begin counting
down from 36 to zero.

b.

The thermostat display will go blank, then will
display the current time and temperature.

c.

Release keys, the program has reverted to the
preprogrammed time and temperature settings.

Setting Temperature Hold

Slide the SYSTEM switch to the heat or cool position.

Temporary Temperature Hold

1.

Press 

 or 

 key to select

a temporary temperature
setting.

NOTE:

The temporary temperature setting is displayed for
approximately 3 seconds and remains in effect until
the next program period. To cancel, press Hold twice.

Indefinite Temperature Hold

The Hold key allows you to indefinitely hold a temperature.
When Hold is active, the letters Hld are displayed continuously.
Hold can be canceled by pressing the Hold key again.

1.

Press Hold

 

2.

Press 

 or 

 key to select

indefinite temperature
setting.

NOTE:

Indefinite hold remains in effect until the Hold key is
pressed to cancel it.

M12629A

M12630A

M12631B

M12632A

M12633B

M12634A

M12636A

M12635A

M12637A

M12638A

M12639B

M12511A

M12640A

TEMPORARY

WED

PM

M12641A

Summary of Contents for TRADELINE T8011R













Reviews: