background image

SPYDER MODEL 5 ROOM CONTROLLERS 

 INSTALLATION GUIDE

 

31-00281ES-01 (EN1B-0664GE51 R0819) 

10 

Automatic MAC Addressing 

In contrast to other controllers (e.g., WEB-8000 controllers, 
whose MAC addresses must be assigned manually 

 done 

using their two dip switches), the WEB-RxxN controller 
features automatic MAC addressing. 
The MAC addresses which the individual WEB-RxxN con-
trollers in the BACnet MS/TP channel assign to themselves 
are not assigned in sequential order. 
Rather, they assign those numbers (MAC Addr) in the range 
of 1 to maxMaster currently not in use by another device in 
the BACnet MS/TP channel (the MAC Addr of "0" is reserved 
by default for the router / plant controller, itself). 
All WEB-RxxN controllers are BACnet MS/TP masters. 
Every master performs periodic polling for the possible 
appearance of new masters. Each master "knows" the 
identity of the "next" master (i.e., that WEB-RxxN controller 
with the next-highest MAC Addr) on the BACnet MS/TP bus 
and to which it must therefore pass the token. The polling 
process includes a search for new masters which might 
have MAC addresses lying between its own MAC address 
and that of the "next" master. 
The property maxMaster specifies the highest-allowable 
address for master nodes. maxMaster is set to 

32

 by 

default, thus guaranteeing that, on a BACnet MS/TP bus 
with, e.g., 32 WEB-RxxN controllers, all of the other WEB-
RxxN controllers will be found. Both the property 
maxMaster and the property MAC address are writeable 
properties that can be changed. 

NOTE:

  You should not attempt to program a MAC Addr 

outside the range of 1 to maxMaster. 

 

#maxMaster

ANCILLARY WEBs MSTP CONTROLLER (WITH MANUAL MAC ADDRESSING)

WEB-RxxN CONTROLLER (WITH AUTOMATIC MAC ADDRESSING)

WEB-8000/

CIPer Model 50 etc

.

 

Fig. 12. Automatic MAC addressing 

In the scenario depicted in Fig.15, some of the controllers 
in the BACnet MS/TP channel do not feature automatic 
MAC addressing; rather, their MAC addresses were 
assigned manually (e.g., using their two dip switches). Thus, 
when a new WEB-RxxN is added to the channel, when its 
automatic MAC addressing function is triggered, it will 
assign itself an available (i.e., unoccupied) MAC address. 
During the automatic MAC addressing process, LED 
behavior #7 (see Table 7) is displayed. 
 

OPERATOR INTERFACES 

LEDs 

The controller features the following LEDs: 

T2 R2 T1 R1

!

 

Fig. 113. Controller LEDs 

 

Table 7. Description of LED behaviors 

symbol 

color 

function, description 

T2 

yellow 

Not used 

R2 

yellow 

Not used 

T1 

yellow 

LED indicating transmission of 

communication signals via the BACnet 

MS/TP interface. 

R1 

yellow 

LED indicating reception of communication 

signals via the BACnet MS/TP interface. 

!

 

yellow 

Status LED indicating firmware problems, 

hardware problems, etc. (see Table 8)

 

green 

Power LED indicating firmware problems, 

hardware problems, etc. (see Table 8). 

 

Table 8. Status LED and power LED behaviors 

Mode 

Power LED 

(green) 

Status LED 

(yellow) 

1  Power failure 

Stays OFF 

Stays OFF 

2  Device error* 

Stays ON 

Stays ON 

3  Firmware download  ON/OFF (1 Hz) 

ON/OFF (1 Hz) 

4  No application 

ON/OFF (0.5 Hz) 

ON/OFF (0.25 Hz) 

5  Broken sensor 

ON/OFF (0.25 Hz)  Stays ON 

6  Short-circuiting 

ON/OFF (0.5 Hz) 

Stays ON 

7  Auto-MAC 

ON/OFF (1 Hz) 

ON/OFF (0.5 Hz) 

8  Unacknowledged 

alarm 

ON/OFF (2 Hz) 

ON/OFF (2 Hz) 

9  Normal operation 

ON/OFF (0.5 Hz) 

Stays OFF 

*Please return the controller for repair. Contact Honeywell 
WEBs Customer Care for assistance.  
 

Service Button 

The Service Button is used to trigger dedicated events. 
It is important to distinguish different controller behaviors 
which are elicited depending upon whether the Service 
Button is pressed when the controller is powering up or 
when it is in normal operation. See the following sub-
sections. 
 

Pressing Service Button during Power-Up 

During controller power-up, pressing the Service Button 
until LED behavior #3 (see Table 8) is displayed will reset 
the controller to its factory settings, which are as follows: 

  The application is cleared from the controller. 

  The MAC address will be set to 0xFF, meaning that the 

controller will now search for a new mac address (Auto 
MAC will be automatically triggered after controller 
power-up). 

Summary of Contents for Spyder 5 WEB-RL6N


























Reviews: