FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet
appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.
RF EXPOSURE WARNING
– The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm)
from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-
transmitter product procedures.
MISE EN GARDE EXPOSITION AUX FREQUENCES RADIO:
L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de
séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.
For the latest documentation and online support information, please go to:
https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
For patent information, see www.honeywell.com/patents
MyWebTech
Warranty
Patents
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved.
6. Reinsert the screen/sensing chamber and press
firmly to set it in place.
7. Reinsert the detector cover back over the
screen/sensing chamber and turn it clockwise until
it locks in place.
8. Reinsert the batteries.
9. Reattach the device to the mounting plate.
8
6
7
Maintenance
(continued)
Battery Replacement
•
Twist the front cover counterclockwise
15 degrees and separate it from the mounting
bracket.
•
Remove both batteries and wait 10 seconds,
then insert two new batteries.
Recommended batteries:
-
Honeywell 466
-
Panasonic CR123A
-
Duracell DL123 or DL123A
NOTE
:
Do not mix old and new batteries, battery
types or manufacturers.
•
Reattach to the detector to the mounting plate.
1
5
Honeywell 466, Panasonic CR123A
Duracell DL123, Duracell DL123A
2
3
30
0
45
10
~
10
sec
4
Replace Batteries
BATTERY CAUTION:
Risk of fire, explosion and burns. Do not recharge,
disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries
properly. Keep away from children.
Specifications:
Batteries
: Two 3V Lithium; Honeywell 466, Panasonic CR123A, Duracell DL 123 or DL 123A
RF Frequency
: 2.4GHz
Tamper
: Cover tamper
Operating Temperature
: 0° to 35° C / 32° to 95° F
Relative Humidity
:
95% max. (Agency Compliance – 93% max.), non-condensing
Maximum Spacing:
50ft x 50ft (refer to National Fire Alarm Code Standard NFPA 72 for
application requirements)
Dimensions
: 13.46 cm Diameter x 4.19 cm Thick / 5.3 in. Diameter x 1.65 in. Thick
Approval Listings:
FCC / IC
ETL Listed – Conforms to UL 268 & UL 521
cETL Listed – Certified to ULC-S529 & ULC-S530
Other Standards:
NFPA 72
ANSI / SIA-CP-01
CSFM
RoHS
NOTE
: Smoke detectors are not to be used
with detector guards unless the combination is
evaluated and found suitable for that purpose.
Ê800-15961PŠ
800-21343 11/15 Rev A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
www.honeywell.com/security
