background image

 

QXe Recorder - Installation Instruction 

 
Touch Screen Assembly 

 

 

QXe Recorder 

 

 

This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up 
functionality in the recorder. Refer to the User manual for detailed operational requirements.   
The QXe Recorders are designed for ease of assembly with minimal disturbance to the rest of the unit. If unsure, please 
return the unit to your supplier for repair or upgrade. 
Removing the case and opening the back of the recorder should only be performed under the following circumstances: 
When an item of hardware requires individual replacement. 
When an item of hardware is to be retrospectively fitted. 
In all other instances it is recommended that the complete unit be returned to an authorised agent or service centre. 
For Agency Approved recorders the product needs to be upgraded or repaired by an Authorized Repair facility 

 

 

 WARNING 

HAZARDOUS VOLTAGES  

Disconnect all power to the recorder before removing the case and attempting any maintenance procedures. 

SAFETY TESTS 

Upon completion of service procedures detailed in this manual two basic safety tests should be performed in order to 
ensure continued safe operation of the instrument. 
Earth Resistance; 25 VDC applied between case and protective earth, bonding resistance should be < 0.1 Ohm. 
Insulation Resistance; 500Vdc applied between the earth terminal, and the live and neutral terminal shorted together, 
insulation resistance to be >2.0 MOhm. (Mega Ohm, NOT milli Ohm) 

Failure to comply with these instructions could result in death or serious injury

 

 

 CAUTION 

OBSERVE ANTI-STATIC PRECAUTIONS 

Refer to BS EN61340-5-1: 2001. Basic specification. Protection of electrostatic sensitive devices. 
Full anti-static precautions MUST be observed when in contact with the electronics of your recorder. 

SAVE DATA, SETUPS AND LAYOUTS 

Removal of PCBs and battery back-up will result in the loss of all non-volatile data.  
Ensure all data and set-ups are saved. 

Failure to comply with these instructions may result in product damage.

 

 

43-TV-33-88 iss.2   GLO   Nov 06   UK 

 

Summary of Contents for QXe Recorder







Reviews: