manualshive.com logo in svg

Honeywell PRO3200, Installation And Configuration Manual, Page: 25 / 35

Share
Download
Honeywell PRO3200 Installation And Configuration Manual Download Page 25

PRO3200 Installation

System Configuration via Web Interface

PRO3200 (PRO32IC)  Installation and Configuration Guide, Document 800-15494

19

4.4  Network Settings

Click the 

Network 

link on the navigation bar to display the Network Settings screen where you can 

select the appropriate option button for dynamic or static IP address configuration:

Figure 7:    PRO3200 Web Server Network Settings Screen

Notes:

• The Host Name of This Device field contains the Media Access Control (MAC) address of the 

PRO3200 controller board.

• The users can select the 

Dynamic IP

 option button and reserve an IP address for the MAC 

address, or they can select the other option button and assign a 

Static IP

 address as well.

Dynamic IP Configuration Method

1. Click the 

Dynamic IP 

option button to select the Dynamic Host Configuration Protocol 

(DHCP) method to obtain IP address automatically. 

2. Click 

OK

.

Note:  

The WIN-PAK communicates with the PRO3200 panel using an IP address. If you must use the 

Dynamic IP option because of your network policies or configuration, you must reserve an IP address 
at the DHCP server for the MAC (Media Access Control) address in the PRO3200 panel. The MAC 
address is a unique identifier attached to network adapters. Each time the PRO3200 panel requests an 
IP address, the DHCP server will assign the address that was reserved for it.

Summary of Contents for PRO3200




































Reviews:

No comments