N500-77-00 3 I56-1803-010
FIGURE 6C. INSTALLATION OF XP10-M MODULE IN FRONT CHASSIS
POSITION:
Step 1: Insert the bottom edge of the XP10-M module down into a front slot
of the chassis.
Step 2: Carefully swing the upper edge of the board towards the back of the
chassis until it touches the 11⁄4˝ (31.75mm) standoffs installed on the
rear module.
Step 3: Align two 4-40 screws with the two standoffs and tighten.
Step 4: Address and wire the modules according to the instructions in this
manual.
WIRING
NOTE: All wiring must conform to applicable local codes, ordances, and regu-
lations.
1. Install module wiring in accordance with the job drawings and appropri-
ate wiring diagrams.
2. All wiring to the XP10-M is done via terminal blocks. In order to properly
make electrical connections strip approximately 1⁄4˝ of insulation from
the end of wire, sliding the bare end of the wire under the clamping plate
screw.
3. Set the address on the modules per the job drawing. Use the rotary code
switches to set the address of the first module (between 01 and 150).
In Class B operation, the remaining modules are automatically assigned to the
next nine higher addresses. For example, if the base address switch is set to
28, the next nine modules will be addressed to 29, 30, 31, 32, 33, 34, 35, 36,
and 37.
The module is shipped in Class B position, remove shunt for Class A. When
operating in Class A, alternate modules are paired together (+0/+1, +2/+3,
+4/+5, +6/+7, +8/+9), resulting in a total of five modules. For example,
if the base address switch is set to 28, then 30, 32, 34 and 36 will be automati-
cally assigned to the modules while 29, 31, 33, 35 and 37 are available to be
used for other modules on the SLC. For Class A and B operation, DO NOT
set the lowest address above 150, as the other modules will be assigned to
nonexistent addresses.
NOTE: All references to power limited represent “Power Limited (Class 2)”.
NOTE: The XP10-M must have power cycled for shunt changes to take effect.
NOTE: Some panels support extended addressing. In order to set the module
above address 99 on compatible systems, carefully remove the stop on
the upper rotary switch (see Figure 7). If the panel does not support
extended addressing, do not set the lowest address above 90.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
C0227-00
FIGURE. 7:
TENS
0
7 8
6
5
4
3
2
1
9
10
11
12
13
14
15
NOTE: Power must not be applied to the unit when changing functionality of
the shunts.
4. A shunt is provided to disable a maximum of two unused modules in
Class B operation and one unused module in Class A operation. Modules
are disabled from the highest address and work downward. If two mod-
ules are disabled, the lowest eight addresses will be functional, while the
highest two will be disabled. For example, in Class B operation, if the
shunt for Address Disable is placed on “two” and the base switch is set
to 28, the modules will be assigned to 28, 29, 30, 31, 32, 33, 34 and 35
while disabling the highest two positions.
5. A communications loss feature is available on some panels. Upon a com-
munication loss, due to a microprocessor failure at the control unit, the
XP10-M will send a signal to the control unit to activate the notification
device circuits upon initiating of an alarm on the XP10-M. A single shunt
is used to enable (shunt on) or disable (shunt off) this feature for all
modules on the board.
NOTE: Place unused shunts on single pin to store on board for future use.
WIRING NOTES
Power-limited circuits must employ type FPL, FPLR, or FPLP cable as required
by Article 760 of the NEC.
PROGRAMMING
The XP10-M module operates with the following Fire Alarm Control Panels:
• AM2020/AFP1010
• AFP-200
• AFP-300/AFP-400
• S-5000 with AIM-200
• AFC-600
• NFS-640
• NFS-3030
The modules are programmed as devices in each system according to the pro-
gramming instructions in the appropriate FACP manual.
C0226-01
2
3
1