COMPATIBILITY REQUIREMENTS
To ensure proper operation, this module shall be connected to a compatible
Notifier system control panel.
COMPONENTS
Following are descriptions of the XP10-M mounting frameworks. There are
two mounting options for XP10-M modules:
• Up to six XP10-M modules can be installed on a CHS-6 in a CAB-3 Series
cabinet, CAB-4 Series cabinet or BB-25 cabinet.
• One or two XP10-M modules can be installed in a BB-XP cabinet.
Chassis
The CHS-6 chassis is used to mount XP10-M modules in a BB-25, CAB-3 or
CAB-4 Series cabinet. It accommodates up to six XP10-M modules in a single
cabinet row three modules wide and two modules deep.
FIGURE 1. CHS-6 CHASSIS:
The BB-XP cabinet has a built-in chassis that will accommodate one or two
XP10-M modules.
FIGURE 2. BB-XP CABINET:
N500-77-00 1 I56-1803-010
XP10-M Ten Input Monitor Module
SPECIFICATIONS
Normal Operating Voltage:
15-32 VDC
Stand-By Current:
3.75 mA @ 24V
Alarm Current:
55 mA (assumes all ten LEDs solid on)
Temperature Range:
32°F to 120°F (0°C to 49°C)
Humidity:
10 to 85% Noncondensing
Dimensions:
6.8˝H x 5.8˝W x 1.25˝D
Accessories:
CHS-6 Chassis; BB-25 Cabinet; BB-XP Cabinet; CAB-3 Series Cabinet; CAB-4 Series Cabinet
Wire Gauge:
12-18 AWG
Maximum SLC Wiring Resistance:
40 Ohms
Maximum IDC Wiring Resistance:
1500 Ohms
Maximum IDC Voltage:
10.2 VDC
Maximum IDC Current:
240µA (each circuit)
C0202-00
C0236-01
BEFORE INSTALLING
If the modules will be installed in an existing operational system, inform the
operator and local authority that the system will be temporarily out of service.
Disconnect the power to the control panel before installing the modules. This
system contains static sensitive components. Always ground yourself with a
proper wrist strap before handling any circuits so that static charges are re-
moved from the body. The housing cabinet should be metallic and suitably
grounded.
NOTICE:
This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The XP10-M Ten Input Monitor Module is intended for use in an intelligent
alarm system. Each monitor module is intended to interface between a control
panel and normally open contact devices, such as pull stations. A common
SLC input is used for all modules, and the initiating device loops share a
common supervisory supply and ground. Otherwise, each monitor operates
independently from the others. Each module has its own unique address.
A pair of rotary code switches is used to set the address of the first module
from 01 to 150. The remaining modules are automatically assigned to the next
nine higher addresses. Provisions are included for disabling a maximum of
two unused modules to release the addresses to be used elsewhere. Each mod-
ule also has panel controlled green LED indicators. The panel can cause the
LEDs to blink, latch on, or latch off.
Included:
(6) 1 x 4 Terminal Blocks (2) 1
1
/
4
″
(32mm) Stand offs
(4) Machine Screws (3) Shunts (10) 47k Ohm
End of Line Resistors
(2) Nuts
Shipped on Board:
(1) Shunt in Class A/B position
(Shipped in Class B position, remove shunt for Class A)
I56-180
3-0
10
INSTALLATION AND MAINTENANCE INSTRUCTIONS
12 Clintonville Road
Northford, CT 06472-1653
Phone: 203.484.7161
0 1
2 3 4 5 6
78
9
0
78
65
4
3
21
910
11
1213
14
15
BA
SE
AD
DR
ES
S
AD
DR
ES
S
DIS
AB
LE
NO
NE
ON
E
TW
O
THR
EE
0 1
2 3 4 5 6
78
9
0
78
65
4
3
21
910
11
1213
14
15
BA
SE
ADDRE
SS
ADD
RE
SS
DI
SA
BL
E
NONE
ON
E
TW
O
THR
EE
C0234-00
MOUNT WITH
SELF-THREADING SCREWS
TO BACK OF CABINET