Honeywell NOTIFIER UDACT-2 Instruction Manual Download Page 44

Page: 44 / 52

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

Panel-Specific Information

AM2020/AFP1010 (UL 8th)

Connect 24 VDC filtered, regulated power from the MPS-24A or MPS-24B (Main Power Supply) to +24V and -24V terminals on the

UDACT-2.

Notes

Recommended wire is 12 AWG (3.25mm

) to 18 AWG (0.75mm

), twisted pair, shielded cable. Connect only one end of shield: a)

shield may be connected to cabinet (earth ground) at fire alarm panel, or b) shield may be connected to TB1 Common at the

UDACT-2 as shown in Figure A.12.

Conduit is required for external wire runs. Consult local building codes.

Refer to "Specifications" on page 8 for power requirements.

Below is a remote installation of a UDACT-2 with an AM2020/AFP1010 using an MPS-24A main power supply:

NOTE:

The shield end that is not connected should be insulated to prevent accidental grounding. Do not connect both ends of shield

under any circumstance since a ground fault may result.

To Phone Lines
(supervised)

Solid Earth Ground

Connection

MPS-24A

SIB-2048

EIA-485

Interface

act2

-a

a_a

CAB-3/4 Series Cabinet

Wires in

conduit

Remote Cabinet

Figure A.12 UDACT-2 and

AM2020/AFP1010

with MPS-24A

Summary of Contents for NOTIFIER UDACT-2





















































Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands

Honeywell NOTIFIER UDACT-2, Instruction Manual

Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands