manualshive.com logo in svg

Honeywell NOTIFIER LCD-160, Manual

Share
Download
Honeywell NOTIFIER LCD-160 Manual Download Page 31

LCD-160 Manual —

 P/N 51850:D2 10/07/2016  

31

Programming Screens

Screen Displays

Figure 9.2  Graphic Screen (No Off-Normal Events)

Soft Keys

MAIN MENU

 - Press this key to display the “Main Menu.” The text of this soft key will appear over 

any graphic that extends into the last line of the display. 

9.1  Programming Screens

Once the system has been physically installed, programming may begin. The user may program an 
LCD-160 at anytime, except while there is an unacknowledged alarm present.

9.1.1  Setting the Programming Switch

The LCD-160’s 
programming switch 
must be enabled to 
program the LCD-160.

Set dip switch 1 on 
SW17 to permit 
programming on the 
LCD-160. SW17 is 
located on the bottom 
edge of the LCD-160 
board. To enable, use a 
small screwdriver to 
slide the switch up 
towards the display. To 
disable, slide the switch 
down away from the 
display.

L A K E S I D E G E N E R A L H O S P I T A L

S Y S T E M N O R M A L

1 1 : 5 8 : 4 5 A

T U E J A N 1 2 , 2 0 1 6

M A I N M E N U

LCD160SW17.wmf

The Programming 
Switch is enabled. 
Switch 1 is ON. The 
slider is towards the 
display screen.

DISPLAY

Figure 9.3  SW17(Programming Switch Enabled)

NOTE:

Switches 3 and 4 

MUST

 remain in the disabled position.

Summary of Contents for NOTIFIER LCD-160

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands