manualshive.com logo in svg

Honeywell NOTIFIER AM-8200, Installation Manual, Page: 16 / 46

Share
Download
Honeywell NOTIFIER AM-8200 Installation Manual Download Page 16

AM-8200 

Installation Manual

 

PAGE - 13 

AM8200_manu-inst 

 Doc. M-162.2-AM8200-ENG Rev A.2 

NOTIFIER ITALIA 

Current consumption from Power Supply 

  Current from power supply in

 Normal Condition

 : 

 

 

 

AM-8200-KLCD (CPU-AM-8200)

 Board at nominal voltage (29Vdc): 179mA 

 

 

AM-82-BBMB (CPU-AM8200BB)

 Board at nominal voltage (29Vdc): 135mA 

 

 

LIB-8200

 

(LIB)

 Board at nominal voltage (29Vdc): 50mA 

 

 

AM82-2S2C (INTERFACE RS232/485/CAN-BUS) 

at nominal voltage (29Vdc): 28mA

  

 

AM82-BST-C (AMPLIFIER BOARD CAN-BUS)

 at nominal voltage (29Vdc): 39mA

 

 

  Current from power supply 

in Alarm Condition  

 

 

AM-8200-KLCD (CPU-AM-8200)

 Board at nominal voltage (29Vdc): 345mA 

 

 

AM-82-BBMB (CPU-AM8200BB)

 Board at nominal voltage (29Vdc): 177mA 

 

 

LIB-8200

 

(LIB)

 Board at nominal voltage (29Vdc): 92mA 

 

 

AM82-2S2C (INTERFACE RS232/485/CAN-BUS) 

at nominal voltage (29Vdc): 28mA

  

 

AM82-BST-C (AMPLIFIER BOARD CAN-BUS)

 at nominal voltage (29Vdc): 39mA

 

 

Current consumption from battery  

  Current from battery in 

Normal Condition

 in the absence of mains voltage 230Vac: 

 

 

 

AM-8200-KLCD (CPU-AM-8200)

 Board at nominal voltage (24Vdc): 113mA 

 

 

AM-82-BBMB (CPU-AM-8200BB)

 Board Card at nominal voltage (24Vdc): 95mA 

 

 

LIB-8200

 

(LIB)

 at nominal voltage (24Vdc): 53mA 

 

 

AM82-2S2C (INTERFACE RS232/485/CAN-BUS) 

 at nominal voltage (24Vdc): 32mA 

 

 

AM82-BST-C (AMPLIFIER BOARD CAN-BUS)

 at nominal voltage (24Vdc): 45mA

 

 

 

  Current from battery 

in Alarm Condition 

in the absence of mains voltage 230 Vac:

 

 

 

AM-8200-KLCD (CPU-AM-8200)

 Board at nominal voltage (24Vdc): 255mA 

 

 

AM-82-BBMB (CPU-AM-8200BB)

 Board at nominal voltage (24Vdc): 95mA 

 

 

LIB-8200

 

(LIB)

 at nominal voltage (24Vdc): 53mA 

 

 

AM82-2S2C (INTERFACE RS232/485/CAN-BUS) 

 at nominal voltage (24Vdc): 32mA 

 

 

AM82-BST-C (AMPLIFIER BOARD CAN-BUS)

 at nominal voltage (24Vdc): 45mA

 

 
 
 

 

See the appendix at the end of this manual for proper battery calculation in Stand-by and in Alarm 
condition.

Summary of Contents for NOTIFIER AM-8200















































Reviews:

No comments