manualshive.com logo in svg

Honeywell NetAXS-123, Installation Manual, Page: 46 / 76

Share
Download
Honeywell NetAXS-123 Installation Manual Download Page 46

38

www.honeywell.com

Installing the NetAXS-123 Panels

Installation

Note:  

Address 0 is not a valid setting.

b. Both DIP Switch 8 and DIP Switch 9 need to be either ON or OFF to be properly 

configured.

Table 9:  

NetAXS-123 SW2 DIP Switch Settings

S1

a

S2

a

Selection

OFF

OFF

RS-485_2 termination (EOL) DISABLED

ON

ON

RS-485_2 termination (EOL) ENABLED (FUTURE) (Default)

a. Both DIP Switch 1 and DIP Switch 2 need to be either ON or OFF to be properly 

configured.

Note

: When you use the DIP switches to reset a panel to the original factory default 

values, the Event History is lost and any customized databases are removed, so the 
panel is reset with the original factory default database. This does not affect the 
Ethernet IP address.
You can also use this ASCII command:

_I=pn_R

 

This command resets the panel to the original factory default values, but it only 
removes the customized databases and restores the original factory default 
database. The Event History is retained.

To reset the panel to the factory default values:

1. Make a note of the existing settings on SW1 DIP switches.

2. While the panel is powered up, turn all DIP switches to the OFF position.

3. Power down, then power the panel back up.

4. Wait for the panel to come up. The RUN LED should flicker fast.

5. Set the DIP switches back to their original positions.

6. Power down, then power the panel back up. 

7. After the the panel comes up, the RUN LED should flash normal.

The panel is now reset to the original factory default values.

Summary of Contents for NetAXS-123













































































Reviews:

No comments