manualshive.com logo in svg

Honeywell MN7510A2001, Installation Instructions Manual, Page: 7 / 12

Share
Download
Honeywell MN7510A2001 Installation Instructions Manual Download Page 7

VB6 SERIES 6-WAY CONTROL BALL VALVES AND ACTUATORS - INSTALLATION INSTRUCTIONS

 7

Printed in USA

31-00380M-02

Electrical Installation

The most important part of the electrical installa

-

tion is the power supply for the actuator.

1. Unscrew the actuator wiring cover in order to 

access to the terminal block(s) as shown 

below.

2. Perform the wiring of actuator using Figure 

13 to Figure 15 as per the required 

application.

3. If necessary, use the appropriate electrical 

cable conduits and cable gland to properly 

secure the actuator wiring.

4. Replace the wiring cover once done. 

Actuator Run modes

The function selection switch (see Figure 16) can

be used to place the actuator into any one of two

different modes:
•

Modulating run mode 

•

Floating/2-position run mode

•

Service/Off mode.

Caution:  To avoid personal injury 

(electrical shock) and to prevent 

equipment damage, before 

installation, you must remove power.

Figure 12. Removable Access Cover 

Figure 13. MN7510 (Modulating Mode)

Figure 14. MN7510 (Floating Mode)

Figure 15. 

MN7510 (2-Position Mode).

 

Figure 16. Function Selection Switch 

Summary of Contents for MN7510A2001













Reviews:

No comments