manualshive.com logo in svg

Honeywell MiniZone EMM-3, Product Data, Page: 5 / 12

Share
Download
Honeywell MiniZone EMM-3 Product Data Download Page 5

EMM-3 ELECTRONIC MINIZONE™ PANEL

5

68-3041-2

(1) Zone 3 damper is open. Zone 3 LED on EMM-3 

is green.

(2) Zone 1 and 2 dampers are closed. Zone 1 and 2 

LED on EMM-3 are off.

(3) Heating equipment is activated. SYSTEM LED is 

red.

(4) Continue wiring the system.

CAUTION

Voltage Hazard. 

Can cause electrical shock or equipment damage.

Disconnect power before continuing installation.

13.

Reconnect power to EMM-3.

14.

Continue troubleshooting system in Cool mode.

a. Set Zone 1 thermostat to Cool mode and Zones 2 

and 3 thermostats to off.

b. Zone 1 damper is open. Zone 1 LED on EMM-3 is 

green.

c. Zones 1 and 3 dampers are closed. Zones 2 and 3 

LED on EMM-3 are off.

d. Cooling equipment is activated. SYSTEM LED is 

green.

e. Repeat procedure for zones 2 and 3. Continue wir-

ing the system.

CAUTION

Voltage Hazard. 

Can cause electrical shock or equipment damage.

Disconnect power before continuing installation.

15.

Reconnect power to EMM-3

16.

Check out fan operation.

a. Set Zone 1 thermostat fan switch to On, and Zones 

2 and 3 thermostats to Auto.

b. Zone 1 damper is open. Zone 1 LED on EMM-3 is 

green.

c. Zones 2 and 3 dampers are closed. Zones 2 and 3 

LED on EMM-3 are off.

d. Fan equipment is activated. SYSTEM LED is off.

e. Repeat procedure for zones 2 and 3. Continue wir-

ing the system.

CAUTION

Voltage Hazard. 

Can cause electrical shock or equipment damage.

Disconnect power before continuing installation.

17.

Connect DATS Sensor to EMM-3 (optional).

a. Reconnect power to EMM-3.

b. If system is in Purge mode, press PURGE OVER-

RIDE on EMM-3.

c. Verify SYSTEM LED is no longer flashing. This con-

firms proper DATS operation. (Flashing occurs in 

Idle and Fan modes only.)

System Zone 1 Zone 2 Zone 3

LED

Red

Off

Off

Green

System 

Operation

Heat on Closed

Closed

Open

System

Zone 1

Zone 2 Zone 3

LED

Green

Green

Off Off 

System 

Operation

Cool on Open

Closed

Closed

System

Zone 1

Zone 2 Zone 3

LED

Off

Green

Off Off 

System 

Operation

Fan on

Open

Closed

Closed

Summary of Contents for MiniZone EMM-3













Reviews:

No comments