Honeywell LP916A-C Installation Instructions Manual Download Page 8 | Manualshive

Page: 8 / 8

Honeywell LP916A-C Installation Instructions Manual Download Page 8

8

LP916A-C PNEUMATIC REMOTE BULB THERMOSTATS

95-5559

95-5559 Rev. 2-90 Printed in U.S.A.

Home and Building Control
Honeywell Limited-Honeywell Limitée
155 Gordon Baker Road
North York, Ontario
M2H 2C9

Home and Building Control
Honeywell Inc.
Honeywell Plaza
P.O. Box 524
Minneapolis MN 55408-0524

Helping You Control Your World

LP916B Switchover Point Adjustment

A

Back off switchover spring adjusting nut (Fig. 18) until
flush with stud.

B

Calibrate per Steps 1 through 5 of LP916A and C
calibration. Increase branchline pressure by rotating
control shaft clockwise. Allow enough time (up to three
minutes) for branch pressure to build up.

C

Lower main line pressure to 16.5 psi (113 kPa). Tighten
switchover spring adjusting nut until branchline
pressure begins to increase. Allow enough time (up to
three minutes) for branch pressure to build up and
observe WARNING in LP916A and C calibration.

D

Except LP916B1058, lower main line pressure to 13 psi
(90 kPa). Adjust switchover lever stop to 8 psi (55 kPa)
branchline pressure. Increase branchline pressure by
raising lever stop. For LP916B1058, lower mainline
pressure to 9 psi (62 kPa) and adjust switchover lever
stop to 6 psi (41 kPa) branchline pressure.

Fig. 18. LP916B automatic switchover mechanism.

SWITCHOVER
LEVER STOP

SWITCHOVER
SPRING
ADJUSTING NUT

STUD

M7997

«
...
6
7
8

Summary of Contents for LP916A-C









Reviews:

No comments