Honeywell L91A Product Data Download Page 1

PRODUCT DATA

Put UPC Code Here

60-2152—08

L91A,B,D Proportioning
Pressuretrol

®

 Controllers

APPLICATION

L91 Proportioning Pressuretrol

®

 Controllers are Series 90 

Modulating Pressure Controllers that provide direct control of 

modulating motors or valves used on automatic burners or 

steam heating systems.

FEATURES

• Models available for pressure systems up to 300 psi 

(2068 kPa).

• May be used with steam, air, noncombustible gases, or 

other fluids noncorrosive to brass or phos-bronze (300 

psi model) bellows.

• When used with steam boilers, a steam trap (siphon 

loop) is recommended.

• Wiper on controller potentiometer moves in response 

to pressure changes.

• L91D has two potentiometers for unison control of two 

motors.

• L91B,D models have adjustable proportioning 

(throttling) range to allow selection of desired 

pressure control range.

• Adjustments made with screws on case top.
• Large, easily-read scaleplates in both U.S. customary 

(oz/sq. in., psi, or in. Hg) and metric (kPa, MPa, or mm 

Hg) units.

• Steel case with clear plastic cover to observe pressure 

settings and potentiometer action.

• Fitting with 1/4 -18 NPT threads allows rapid 

installation.

• Surface mount with screws through knockout holes in 

case back.

Contents

Application 1

Features 1

Specifications

 2

Installation 5

Wiring 6

Checkout

 8

Service Information 

9

Summary of Contents for L91A













Reviews: