manualshive.com logo in svg

Honeywell KromSchroder IC 40, Technical Information, Page: 22 / 72

Share
Download
Honeywell KromSchroder IC 40 Technical Information Download Page 22

IC 40 · Edition 07.18

22

middle

t [s]

high

low

closed

DI 1

DI 2

t [s]

t

1

 

t

2

t

3

t

4

t

5

t

6

Function

Operating mode 6

DI 1 with continuous signal, for instance resulting from 
inversion of the logic, see page 48 (Switching logic):

The actuator operates in high/low (high/closed) inter-

mittent mode via digital input DI 2 with two successive 
running times up to 51 s (2 x 25.5 s).
DI 1 and DI 2 are connected in parallel: 

The actuator operates with one signal in high/closed 

intermittent mode with three successive running times 
up to 76.5 s (3 x 25.5 s).
With three successive running times via interpolation 
points, it is possible to change the opening character-
istic of the butterfly valve. For example, the character-
istic of the air circuit can be adapted to that of the gas 
circuit.

Control via two digital inputs

If all possible combinations of the two inputs are used, 
for instance by a PLC control system, it is possible to 
implement high/middle/low/closed intermittent mode 
(3 stages plus the “closed” position).
Possible parameter set for this operating mode: 
P 68001, see page 45 (Parameter sets).

Summary of Contents for KromSchroder IC 40









































































Reviews:

No comments